97BlackAckCL

iTrader: (6)

I love pioneers, I say go for it

And I hear ya, I love my Teins too

a2ndragoon89

Yeah, finally have some money from work. Also tax refunds came back. 1g in my pocket lol. Started my new job midway through the year so I got most of my taxes back this time around. Probably going to replace my speakers with jbl or polk too. Teins for our cars are much cheaper than when I first bought them too. it's like 750 on ebay right now or "make an offer" which you may save 100-200.

asianspec

iTrader: (1)

Going to buy basics in April or if I get a good tax return earlier than that.

ACCLKL

Got a new battery after having the previous one testing bad at autozone. The Duralast Gold Battery is taller than the triple A one i had in there and the securing bracket does not reach the frame casing the battery sits in. Do any of you brackets on your batteries or dont worry with them?

timeizmoney22

I have a battery with the same situation. It's been unstrapped for months without incident.

a2ndragoon89

My bracket is broken, but I ghetto rigged it with metal wires. works fine for me.

p8ntbllr466

bungee cord battery hold down ftw

97BlackAckCL

iTrader: (6)

you can get new tie downs for like $12 a piece

SleeperishCL

I just got new tires! Bridgestone Potenza Pole Positions, just on, but they are sticky and quiet AND were pretty cheap I think.... $133 per tire.

timeizmoney22

Nice! I have Toyo Proxes 4 215/45R/17 and they are way nosier than I expected! Slowing down from 10mph-a stop and the car sounds like a german tank!

timeizmoney22

Seafoam 1/3 in pvc, 1/3 in crank, and 1/3 in gas tank. 25 mile "spirited run" then synthetic oil change. Feul filter as well. OBX throttle body spacer should be here Teusday.

Cocoa

iTrader: (2)

The shop recently listed the car at $3,800. If it does not sell within 30 days, they will be parting it out. D:

97BlackAckCL

iTrader: (6)

asianspec

iTrader: (1)

@ mauricio's shop?

Cocoa

iTrader: (2)

^ yeap yeap

DaInFaMMuS1

Ohhhhh nooooo

SupraManAG

So sad. Ive lost faith

asianspec

iTrader: (1)

But after u race Percy.

GhettoNinja06

iTrader: (1)

Just do it already!!
That's why I'm saying things haven't changed

TAco23

Attempted to change my fuel filter. What a PITA. Leaking like crazy, don't ever buy Oreilly brand. Doesn't seal right. Btw anyone know if the banjo fitting holes have to line up with the holes on the bolt? If it does that shit ain't tight enough.

975speed

Since I fixed the passenger quarter panel yesterday I thought I would tackle the bumper cover tody. It did not line up very well the PO had backed into something in the past and pushed the cover in and was bulging out on the pass side, I pulled the tail light out and the trunk plastic, as soon as I pulled the light I could see the damage in side the the light opening so with a couple of body hammers and dollies I got it back it shape then had to push the mounting bosses out a little for the light to get it lined up, I found the hole that the stud for the inner bumper support that mounts to the body,I had a long drift put it threw the hole right on the stud and with a few good smacks with a 3 pound hammer I was able to push the support out and the cover. Then a little massaging to the very outer channel of the support pulled the cover right out and inline with the fender,trunk and light. Then threw some new spark plugs in done for today. Next week repaint rims.

timeizmoney22

Can't wait to see how the panel came out. I couldn't expand the pic in your garage so you somehow have to get me a pic. If your willing (and I would compensate) I'm going to locate a fender and you could help me with mine.

975speed

http://www.flickr.com/photos/97acura/

You can check out pics of the patch here now.

hwdp420pl

the rust on my pass side rear is getting worse and worse i need to do this too

975speed

I is not that hard to do,take your time welding spot weld only let every other weld cool off do not get the part to hot after a few spots walk away let it cool off, slow and steady I have a lincoln sp135 plus mig for body work.It is a 110volt unit.
The front fender fits well, the angle on the tip has to be straightened a little so the bumper cover will sit flush.

hwdp420pl

Did you use a pass side fender ? i have been thinking of doing this but making the fender wider about a inch with a little bit of body work. to make it more aggresive with the wheels.

975speed

To repair the passenger side quarter you use the drivers front fender. For the drivers side quarter repair you would use the passenger side front fender.

975speed

Today I put the CL up on the lift and checked all the suspension parts over, I have a clunk/rattle in the front end that I heard when I was hitting bumps. Checked front and back besides the bushings being cracked on the control arms in the front the passenger side lower ball joint is toast, grabbed it with a big set of channel locks and it moved alot! So that will be the next job.
Also today I took the right rear ABS sensor out and got the broken stud out that holds the ABS sensor on the right rear knuckle.

975speed

Added to the post

97BlackAckCL

iTrader: (6)

Finally ordering a new front bumper

gmsron

I kicked my CL out of the garage for this...

Full WW lip kit, Tein SS, Gram Lights 47s and more for sale!

975speed

Put 4 new pro meter stock size tires on the CL today.

hobo2424

i did oil change(switched to mobil 1 full synthetic), changed battery(duralast gold) and found out my c/v boot on my left front is cut (thats geting fixed on Saturday for free.)
The battery was free to because someone at autozone gave me the wrong battery a long time ago.
with this string of luck i should play the lotto.

spencer_homer

CLEAN s2K!

i got ahold of kryanite. Coils coming early next week. getting my wheels ready before then!

South Jersey CL

spent 2 hours cleaning the car. wash, wax, armor all the inside. took this pic at the free car wash at my friend's apartment. thought it was cool.

DaInFaMMuS1

Wow that is 1 tall shifter lol.

97BlackAckCL

iTrader: (6)

jeffcosta123

Can anyone point me in the direction of where I can find out if a fuse box harness (for radio, gauges, etc.) from a 98 Acura CL 3.0 is compatible with the 97 Acura CL 3.0?

asianspec

iTrader: (1)

junkyard

975speed

I buffed the headlights today with scratchout for plastic and a 4" buffing pad on my drill they look brand new!