davidle84

Are you going to be lowered? If not, then yes that will fit. I suggest you should get some kind of suspension because if you don't, it'll look like a 4x4 sedan.

davewhodavedunn

WILL THESE FIT MY 2006 ACURA TL AUTOMATIC?


1.Brand of Rim - EXE KONVEX

2.Rim size (diameter and width) - 19X8.5 FRONT AND REAR
3.Offset - 33mm
4.Brand of tire - Lexani
5.Tire size - 235,35,19
6.Drop Type and Amount - none
7.Will they rub?????
8. Transmission type automatic

gerzand

iTrader: (3)

Rim size (diameter and width) - 19X8.0 all around
Offset - 45mm
Brand of tire - (Dunlop) Fierce Instinct ZR
Tire size - 245/35/19
Drop Type and Amount - 1.8''
Will they rub at full wheel lock?
Transmission type: 5AT

killersrt

I'm looking to get the deepest dish possible, without rolling the fenders, nor using spacers. I'll probably stretch a 225 tire on the rims. Just need to know the best matching offset

Viper45

i'm not lowered yet...but these are what I am looking at...getting a helluva deal on them...unfortunatley not 19" but 18's are not bad either...
Specs are:
Fit: 5x114.3
(Front) 18x9.5 (offset +33) . . . 2.5 inch Lip (A-DISK)
(Rear) 18x10 (offset +22) . . . 4.5 inch Lip (O-DISK)
Tires are: 235/40/18 (Falken 912)


would this work? how much would I have to roll the fenders...hope there is no pull needed. any input would be great. I am looking at lowering the car just with springs at this time as I cannot be bothered to pay for coils....thanks guys

davewhodavedunn

Dont get 18's on this car, they look small than the oem wheels...not worth it!

killersrt

Depends on the design of the wheel

UAeight08

so i went to a local wheel shop the other day and was told by one of the guys there that the 5zigen ZR+520s will not fit in the 19x9 +37 setup.

stillhere153

iTrader: (1)

the best toe to save tires is no toe at all

yes you will have to pull the fendeers slightly

yeah I think they won't clear the brembos at the +38... I'd say with a 5mm spacer they would... the lower +15 and +20 offset is just way too low... but you can contact "bforbrian" he can help you out on getting the lower offset to fit

i"d stick with 245/30-20
yeah 265/30-19 is the widest treadwidth because anything wider and you have to make sure it doesn't rub the strut

235/35-19 or 245/35-19front
255/30-19 rear (might require rolling)
245/35-19 all around will not require rolling

I believe there is +35 offset, but they do not clear the brakes with that offset, 5mm spacer in this case tires would have to be 235/35-19

YES ... that wheel has been ran by atleast 5 members on here

ur good... on the fitment no rubbing

you wont have to stretch the 225 on the front of the pentas... for the rear there's a x9.5 I believe that is a hefty enough lip

you'll be running 235/40-18 all around? you will need to roll and slightly pull the rear fenders

I disagree... if you go hella wide they look good


if the car has no brembos, they fit 100% guaranteed

UAeight08

yes, that's what i thought. he probably missed that little detail because he didn't even ask me what trans i have. i'll definitely take your word for it. plus, these wheels have already been put on a TL before with no problems. thanks.

gqdabien

Thanks for the answers stillhere153, I originally asked this:

2006 Acura TL Base

Rim specs:
XXR 006
Size: 2 Front Rims are 19X8.5 about 2" Lip
Size: 2 Rear Rims are 19X9.5 about 3" Lip
Bolt Pattern: 5X4.5 (114.3) and 5X120
Offset: +35mm

Future drop:
1-1.5"

Aside from just having to use 245/35-19 size tire. Will the rims clear the stock brakes without any type of spacers and things? Thanks again!! Great Thread!

UAeight08

what is the widest possible wheel that will fit the fronts on an automatic 05 base?

diskinnect

iTrader: (2)

will these fit onto my car. how much of a stretch will i need and how low will i be able to drop it?

my fenders are rolled all around. but would i also need to pull them?

Questions on Wheels
Wheel Make/Model: MB Motorsports Battle
Wheel Size (**X**): 18x9.5
Wheel Offset (+**): +15
If lowered (amount): 2.5 inches



tires:
nankang ns2
205/40/18

stretch would look something like this

stillhere153

iTrader: (1)

your description states "BASE" so I gather you DO NOT have brembos... you do not? then don't worry about "brakes"

x9.5 +40

if you rock a 205 on a x9.5 you got BALLS OF BRONZE... mb makes some slightly higher offsets on that specific wheel...
it'll fit w/ rolling the fronts and dialing in some negative camber... but don't go over 60mph

killersrt

Glad I found out about the spacer ahead of time. I would have been pissed if I got my rims, only to find out that I needed to order a spacer and wait again Should I run a spacer on all 4 rims?

diskinnect

iTrader: (2)

what would be an appropriate drop and stretch in order to make it fit?
225 40 18
and 2 inch drop?

undeadboy88

Questions on Wheels
Wheel Make/Model:MSR Mesh style 093
Wheel Size:F 20 x 8.5 R 20 x 10
Wheel Offset :40
If lowered (amount):no
Acuara tl 05

if it doesnt fit does there any way tomake it fit????
link for wheels..http://cgi.ebay.com/ebaymotors/ws/eB...TQ:MOTORS:1123
Thanks you very much

SG81

iTrader: (1)

can someone help me with a question:

what is the OEM wheel spec/offset for an '07 TL w/ Brembo package?

gqdabien

Yup base model so no Brembo's. Will the wheel & tire combo clear front and rear fenders as well as inner struts with a conservative drop? Thanks!

happyboy

Same as every other 3G TL....17x8 +45 offset!

UAeight08

+40 is the lowest i can go?
what will i need to do to make x9.5 +35 fit the fronts? or... will cause too much rubbing when turning?

EAMotorsports

Wheel Make/Model: MSR 093
Wheel Size:F&R 20 x 8.5
Wheel Offset :40
If lowered (amount):1 inch
Acuara tl 04 AT

Will these fit with no rubbing issues and what size tire?

Thanks
EA

chino13com

1.Brand of Rim - vossen

2.Rim size (diameter and width) - 19X8.5 FRONT AND REAR 19x10
3.Offset - 30mm , rear 38mm or 36mm
4.Brand of tire ??
5.Tire size - need help here
6.Drop Type and Amount - slammed
7.what size tire should i go and which offset would be better and why/????
THANKS

Projectmayhem

I have two general questions.

1. What would need to be done to get 19x9 to fit for front and rear with a slight drop? (i.e. Tein HTECH).

2. What would be the best offset for a 19x8.5 wheel? I want a flush look that doesn't rub. I want to get the wheel as far out of the well as I can without making any fender adjustments, etc. If I dropped the car it would be on Tein HTECH or the A-spec.

stillhere153

iTrader: (1)

yea I'd try that

if your car is auto... it fits

ur golden

you can dial in a tiny bit of negative camber and roll the front fenders, just make sure you have someone who knows what they are doing roll ur fronts

that or you can stay above 1.5" drop

235/30-20
or
245/30-20
no rubbing

since you are slammed 225/35-19 front
+38 rear 245/35-19

1. the wheel has to have an offset between +30 and +40 and you can wrap that around 245/35-19

2. 19x8.5 +35 245/35-19 all around

shawdawg17

Wheel Make/Model: Lorenzo WL18
Wheel Size:F&R 20 x 8.5/ 20X 10
Tires: Front 225/35/20 Rear 255/35/20
Wheel Offset :F35/R38
If lowered (amount):stock
Acura tl 08 AT


Wheel Make/Model: Stern SST-8 Hyper Mesh
Wheel Size:F&R 20 x 8.5/ 20 X 9.5
Tires: Front 225/35/20 Rear 255/35/20
Wheel Offset :F38/R35
If lowered (amount):Stock
Acuara tl 08 AT


Will this fit without any problems and also will it affect my speedo much

Thanks

Makstone

I just picked up my first TL, '07 Type-S 6M and I'm looking at wheels. I can see that most members are going with 19x8.5 and I have ruled out 20x8.5 for fear of poor ride quality. I'm considering dropping 1" in the future, should I go with 19x8.5 or 18x8.5? Does ride quality suffer considerably?

ashahidi

Wheel Make/Model: Enkei Aletta
Wheel Size:17 X 7.5
Tires: Kumho Ecsta ASX 235/45/17
Wheel Offset: 38 or 45
Car: 05 Acura TL AT

Will these fit on my existing tires? Thinking of switching from the OEM wheels to these. Thanks!

chinkwapin

iTrader: (1)

need OEM brembo clearance

Questions on Wheels
Wheel Make/Model: Enkei RPF1
Wheel Size (**X**): 18x9.5 front 18x10.5 rear
Wheel Offset (+**): +15, +15
If lowered (amount): 2.5in

i want an aggressive offset and if i get these i'd def raise my car a tad. my question is will they poke too much to the point where it looks really stupid? a little poke is ok for me but nothing excessive.. im also considering:

Questions on Wheels
Wheel Make/Model: Enkei RPF1
Wheel Size (**X**): 19x8.5 front 19x9.5 rear
Wheel Offset (+**): +22, +22
If lowered (amount): 2.5in

Mike_90

Wheel Make/Model: tenzo type M
Wheel Size (**X**): 18*8
Wheel Offset (+**): +45 (I believe)
If lowered (amount): no
bolt pattern: 5-100/114

HRF1

iTrader: (1)

Prodrive GC-07
17x8.5 +54
255/40/17

Would this work and clear the Brembos for a '07 TL-S lowered on Eibach Pro-Kit?

Thanks!

idolize

Questions on Wheels
Wheel Make/Model:Volk VR-G2
Wheel Size (**X**): 19x8.5(fronts) and either 19x9.5 or 19x10.5 for rears
Wheel Offset (+**): 35et
If lowered (amount): 2 inches

rubber:Yokohoma's SDrive's fronts would be 245/35/19s . rears? want to keep it 35profile

fender roll? and 35et offset clear bbk for fronts?

whip:2008 TL-S

stillhere153

iTrader: (1)

on the first set of wheels they fit fine, REAR TIRES SHOULD BE 255/30-20

on the second set the rear will have to be rolled and again the tire size is 255/30-20

the 19 is definitely less cushion than the 18
my rule is 19 with a lip
18 w/out

18 with lip look tiny


that wheel is too narrow minimum spec should be 17x8 +45

that offset is on the low side... so you will have to stretch tires... the +22 is far better looking than the +15


if you don't have brembo they fit, but I would go with the +38 offset


NO... that will easily require a 19mm spacer

+35 should be enough

Bayam0n

will an offset greater then 50, make the wheels extend out, causing rubbing on the fender?

I want to make my wheels flush (I havent put them on yet), so i don't want a tucked in look. I'm running on 245\40\19 x 8.5 offset 40. I hope this would flush, you think I need spacers? and they are deep dish, 1.75 lip (not that deep)

jrtls03

iTrader: (1)

1.Brand of Rim - Enkei RDX 19" wheel

2.Rim size (diameter and width) - 19X8 FRONT AND REAR
3.Offset - 45mm
4. 10mm spacer
5.Brand of tire - don't have tires yet
6.Tire size - 245,35,19
7.Drop Type and Amount - Tein S tech springs

Any issues forseen with this setup?

thanks for the help!

stillhere153

iTrader: (1)

if your car is Auto and NOT a type s... spacers are not required

note: the higher the offset the further away from the fender

thus +40 is closer to the fender than +50

TIRES: that tire size is NOT correct, you need 245/35-19

if your car is Auto and NOT a type s... they will fit
There is a thread where a ton of members are buying these wheels for under $600

jrtls03

iTrader: (1)

if your car is Auto and NOT a type s... they will fit
There is a thread where a ton of members are buying these wheels for under $600[/QUOTE]

my car's an auto. thanks for the help. thats what I paid for them through my local dealership.

Chiquis

New member, '07 TL automatic, stock all around and it's time for wheels and tires, looking for some advice:

Wheel Make/Model: basically mesh style wheels,considering axis penta, work vs-xx, MRR GT-1
Wheel Size (**X**): debate is 19"vs 20", 8.5 vs 9.5 and to stagger or not
Wheel Offset (+**):
If lowered (amount):none

is there any benefit either way 19 vs 20, I heard can't stagger 20"
want as much deep lip as I can get, would be ok to be at wheel-well edge as long as tires not sticking out

Bayam0n

Why is it incorrect, I've seen ppl with 245/45/19 before, what's the difference with 245/40/19? and isn't 245/35/19 considered low profile? I didn't want low profile, but 245/40/19 isn't that much of a difference.

Jesstzn

Here is a tire size calculator , put in your stock size and the 245/40/19 and it will tell you the error caused by the sizing . In reality you should be running a 235/35/19.

http://www.miata.net/garage/tirecalcold.html