StreetKA's CLS6 Thread
#681
Burning Brakes
#685
ok so i finally installed wideband but i notice that car is running a bit rich at wot around 5200-5800 and im not sure why is like that maybe injectors arent in the best shape ?
http://www.youtube.com/watch?v=V21NehH_aHY
replaced also front swaybar links and bushings
my upper balljoints are shot but im getting installed adjustable arms tomorrow so it will be replaced
next week im getting RR bushings done as well
http://www.youtube.com/watch?v=V21NehH_aHY
replaced also front swaybar links and bushings
my upper balljoints are shot but im getting installed adjustable arms tomorrow so it will be replaced
next week im getting RR bushings done as well
#692
03 acura cl type s
iTrader: (1)
Cause I have first hand experience with it and the cat your looking @ is different from ours. Our O2 goes in the cat not before or after.
This pic is from my old cl6 look closely wideband O2 and second O2 with vibrant spacer http://i1119.photobucket.com/albums/...h/dc0fe1df.jpg
This pic is from my old cl6 look closely wideband O2 and second O2 with vibrant spacer http://i1119.photobucket.com/albums/...h/dc0fe1df.jpg
#697
Banned
iTrader: (1)
#698
STAY AWAY from that seller i do NOT recommend buying anything from them. Poor customer service never get any response on my emails or calls. I sent back old resonator for exchange and i never got replacement nor money back. I had to open a case with ebay.
#699
Ingalls adjustable control arms installed - going to alignment next week with new set of Hankooks V12 235/40
i got set of RR bushings but its was too much pain to have it installed so it will wait till i get the rest of the parts and do the clutch first then change all of the parts i was planing to...
i got set of RR bushings but its was too much pain to have it installed so it will wait till i get the rest of the parts and do the clutch first then change all of the parts i was planing to...
#700
Suzuka Master
iTrader: (1)
![Yes](https://acurazine.com/forums/images/smilies/yes.gif)
![ugh](https://acurazine.com/forums/images/smilies/ugh.gif)
My power steering pump is starting to go after 126K, so I ordered all of the OEM seals and bearing for a rebuild. Looking forward to digging into this project. It will cost about $40 + or - compared to a $250 reman. unit.
Going to follow the link below as well as the Helms for the rebuild:
http://www.facebook.com/photo.php?fb...17b400&theater
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
Last edited by zeta; 09-10-2011 at 05:55 PM.
The following users liked this post:
StreetKA (09-10-2011)
#701
i know u did replace rr bushings did you removed axles to undo these bolts ?
thx for the link its good to have something just in case
you can make a DIY based on this one with all sources for seals bearings
thx for the link its good to have something just in case
you can make a DIY based on this one with all sources for seals bearings
Last edited by StreetKA; 09-10-2011 at 06:11 PM.
#702
Suzuka Master
iTrader: (1)
No, it's not necessary. Loosen the self-lock nut (I believe it was 17mm) on the front of the RR first, while it's secured to the LCA. Separate the outer tie rod end, and lower ball joint. This will allow you to swing the whole knuckle assembly forward a bit along with the axle. You'll see what I mean when you are there. Make sure to support it (knuckle) with an extra jackstand or jack because you do'nt want that thing to drop on yourself. Get your 19mm on a breaker bar, push down on the LCA a bit, fit the socket and wrench away. Those two bolts are on at 116 lbs-ft or so, IIRC, so give them hell. hehe
Last edited by zeta; 09-10-2011 at 06:14 PM.
#705
i need some help... since im doing most of the suspension work right now and i want to have piece of mind for a long time what should i replace ?
done is upper control arms with ball joins, swaybar links and bushings, tomorrow RR bushings,
lower ball joints looks ok but should i replace them anyway ?
done is upper control arms with ball joins, swaybar links and bushings, tomorrow RR bushings,
lower ball joints looks ok but should i replace them anyway ?
#707
I welded the bung that comes with aem gauge kit. But i know that there is a wideband kit that doesnt require welding. And it costs like 35$ you simply drill the hole and use their clamp to mount the sensor. If you want i can post a picture of a sensor welded but remember that it must be mounted exact angle
The following users liked this post:
gnuts (09-13-2011)
#712
The following users liked this post:
richardparker (09-13-2011)
The following users liked this post:
Jacobpockros (09-13-2011)
#717
ok so i did the alignment today and put new tires car finally drives like a dream ![Smile](https://acurazine.com/forums/images/smilies/smile.gif)
![](http://i772.photobucket.com/albums/yy9/StreetKa/IMG_2247.jpg)
i also installed xlr8 sidemount that i totally forgot about... no reviews yet but im going tonight for a small car meet so will check them out :P
i can not find time though to do RR bushings, i just dont want to work on it in my garage, waiting for friend to let me use his lift at his shop
![Smile](https://acurazine.com/forums/images/smilies/smile.gif)
![](http://i772.photobucket.com/albums/yy9/StreetKa/IMG_2247.jpg)
i also installed xlr8 sidemount that i totally forgot about... no reviews yet but im going tonight for a small car meet so will check them out :P
i can not find time though to do RR bushings, i just dont want to work on it in my garage, waiting for friend to let me use his lift at his shop
Last edited by StreetKA; 09-14-2011 at 06:29 PM.
#720
Whats up with RDX owners?
iTrader: (9)
Let me know about any meets next week. Im heading to NY this Saturday or Sunday and staying until the following weekend.