The 3G Ramblings & General Discussion Thread
07-13-2012, 04:14 PM
#5441
Chapter Leader (Southern Region)
07-13-2012, 04:15 PM
#5442
Chapter Leader (Southern Region)
A-spec kit and be done with it. 
1/2" won't matter unless you drive like Justn.
1/2" won't matter unless you drive like Justn.
2004, rust, salt, shit, fuck, broke. 
07-13-2012, 04:17 PM
#5444
Race Director
iTrader: (3)
Join Date: Feb 2012
Location: South Florida
Age: 30
Posts: 18,278
Received 3,824 Likes
on
2,847 Posts
Yeah, A-Spec is next.
The following users liked this post:
Undying Dreams (07-14-2012)
07-13-2012, 11:25 PM
#5447
Safety Car
majofo, I just got back from frys and picked up this.......
http://www.frys.com/product/5707222?...H:MAIN_RSLT_PG
haven't removed the old one yet, but hope this one works
http://www.frys.com/product/5707222?...H:MAIN_RSLT_PG
haven't removed the old one yet, but hope this one works
07-14-2012, 02:24 AM
#5449
Chapter Leader (Southern Region)
So you removed the old one and replaced it. Make sure the main atx connector is secure and on right. Make sure you plug in the sata cable to your hard drive as well.
The following users liked this post:
A SiQ TL (07-15-2012)
07-14-2012, 08:00 AM
#5450
Race Director
iTrader: (3)
Join Date: Feb 2012
Location: South Florida
Age: 30
Posts: 18,278
Received 3,824 Likes
on
2,847 Posts
Yes I know they say moar low but I like where it's at.
07-14-2012, 10:29 AM
#5451
-Brandon
I don't think there is anything wrong with your height at the moment. It cuts most of the gap out so you're not a 4x4, but leaves functionality for daily driving. Have you scraped at all yet on your height?
07-14-2012, 01:09 PM
#5452
Chapter Leader (Southern Region)
You're still 4x4 mode. 
The following users liked this post:
UA6~RBP (07-14-2012)
07-14-2012, 01:12 PM
#5453
Race Director
iTrader: (3)
Join Date: Feb 2012
Location: South Florida
Age: 30
Posts: 18,278
Received 3,824 Likes
on
2,847 Posts
07-14-2012, 02:01 PM
#5454
Chapter Leader (Southern Region)
07-14-2012, 02:02 PM
#5455
Chapter Leader (Southern Region)
SiQ.. I see you lurking.
07-14-2012, 02:02 PM
#5456
Chapter Leader (Southern Region)
broham.. make sure that PS is switched to 110/120.. and not 220/240.
07-14-2012, 02:03 PM
#5457
Chapter Leader (Southern Region)
The following users liked this post:
Undying Dreams (07-14-2012)
07-14-2012, 02:21 PM
#5461
Chapter Leader (Southern Region)
07-14-2012, 02:47 PM
#5463
Race Director
iTrader: (3)
Join Date: Feb 2012
Location: South Florida
Age: 30
Posts: 18,278
Received 3,824 Likes
on
2,847 Posts
If you're ordering online I'd check the shipping, shipping to Mars can be quite expensive. 
07-14-2012, 03:51 PM
#5464
Chapter Leader (Southern Region)
Why? is shipping to PA really that much more? 
07-14-2012, 03:58 PM
#5465
Race Director
iTrader: (3)
Join Date: Feb 2012
Location: South Florida
Age: 30
Posts: 18,278
Received 3,824 Likes
on
2,847 Posts
07-14-2012, 04:13 PM
#5466
Chapter Leader (Southern Region)
07-14-2012, 10:52 PM
#5469
Chapter Leader (Southern Region)
You're welcome.
07-14-2012, 11:57 PM
#5470
Chapter Leader (Southern Region)
1 small step for man, 3 large steps for Wet Dreams
07-15-2012, 02:01 AM
#5473
Safety Car
oh, I thanked your post that helped, and pointed out the problem.........
If that is the big connector, that was the problem. Not only did it pop off in my hand when I double checked it today, but there was a second 4 pin connector attached to it on the new psu that my old one didn't have. A friend of mine looked at that and said it needed to be hooked up.
After securing both of them, problem solved.
If that is the big connector, that was the problem. Not only did it pop off in my hand when I double checked it today, but there was a second 4 pin connector attached to it on the new psu that my old one didn't have. A friend of mine looked at that and said it needed to be hooked up.
After securing both of them, problem solved.
07-15-2012, 11:18 AM
#5474
Chapter Leader (Southern Region)
07-15-2012, 11:19 AM
#5475
Chapter Leader (Southern Region)
oh, I thanked your post that helped, and pointed out the problem.........
If that is the big connector, that was the problem. Not only did it pop off in my hand when I double checked it today, but there was a second 4 pin connector attached to it on the new psu that my old one didn't have. A friend of mine looked at that and said it needed to be hooked up.
After securing both of them, problem solved.
If that is the big connector, that was the problem. Not only did it pop off in my hand when I double checked it today, but there was a second 4 pin connector attached to it on the new psu that my old one didn't have. A friend of mine looked at that and said it needed to be hooked up.
After securing both of them, problem solved.
07-15-2012, 08:56 PM
#5479
Chapter Leader (Southern Region)
