When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Really like your trunk setup. Does the 3H not give you the option to "pancake" the car down? (lower front and back at the same time)
Thanks! Spent a lot of time searching for ideas on the trunk setup and I wanted a "functioning trunk" meaning throwing cases of water bottles from Costco and such which I haven't done yet but sadly couldn't fit a check in luggage in the trunk only a carry-on luggage.
I seriously haven't played around with the settings besides the ride preset and getting failure on the height sensors. I don't think Airlift 3p/3h has that feature but yes it bothers me the front lowers faster than the rear granted the front is heavier versus the rear so its logic. But if other Airlift 3p/3h user could chime in, that would be great!
Thanks! Spent a lot of time searching for ideas on the trunk setup and I wanted a "functioning trunk" meaning throwing cases of water bottles from Costco and such which I haven't done yet but sadly couldn't fit a check in luggage in the trunk only a carry-on luggage.
I seriously haven't played around with the settings besides the ride preset and getting failure on the height sensors. I don't think Airlift 3p/3h has that feature but yes it bothers me the front lowers faster than the rear granted the front is heavier versus the rear so its logic. But if other Airlift 3p/3h user could chime in, that would be great!
I'm pretty sure it does have the option I was just curious since I didn't see it used in the video lol.
I want the bracket you used but it seems to be sold out everywhere.
I considered doing a spare tire install but afraid of losing spare tire and then needing it in the future.
I'm installed the RL brake
Any thing new on your car yet?
In for photos!
Just waiting for another shipment from T-Demand front and rear upper arms, tie rod, stabilizer bar and links and that should be a T-Demand complete (unless I want them to make front and rear lower arms), should be here before July if not by June.
According to Ed's it's a yes.
My build is the same as his )
Originally Posted by ed_423
stock:
lowered
1. lowered on megan coilovers
- about -1.75" lower in the front, -1.5" lower in the back. i adjusted my height so
many times that these are just rough estimates.
- front and rear are 4 clicks away from the hardest settings.
- in pics it doesn't seem like it's much of a drop, but everything is different once you start driving. so be aware.
2. Forgestar cf10
- 19x9.5 +42 front, with a 3mm spacer = +39
- 19x9.5 +30 rear
- 235/35/19 michelin ps2 all around. SLIGHT stretch. these tires run true to size or run
large, so the stretch is minimal.
3. J-POWER camber arms
- toe is 0, camber is -1.5/-2
4. Fender work needed!!!!
- rear fender shaved, bumper taps shaved as well. NO PULL NEEDED
- front is slightly pulled, however i didn't need it at all!!
5. Review
- This is a semi aggressive set up, took a lot of time and adjustment to make it perfect
for me to daily drive with it. i think i should be able to go softer on the comfort, but
it's not too bad right now. i don't rub at all, have about 1 finger gap all around.
Over all, it's a good set up for daily driving I think, but gotta drive carefully and do a
lot of research before going for a semi aggressive or super aggressive set up.
how are the height sensors working out with the 1/4" air lines. Bagriders recommended me to switch out to 3/8 lines. I was trying to calibrate in pressure mode because I don't have sensors installed yet. I have 1/4 " lines but it was just going up and down in the front for about 10 minutes and then failed
Bought my setup from Bagriders and was not suggested to run 3/8" lines. I ran the calibration and was stock at step 16 of step 16 and ten minutes then failed as well. I called Airlift and they said my sensors still needs to be slightly relocated. So right now I am running with pressure.
Bought my setup from Bagriders and was not suggested to run 3/8" lines. I ran the calibration and was stock at step 16 of step 16 and ten minutes then failed as well. I called Airlift and they said my sensors still needs to be slightly relocated. So right now I am running with pressure.
Mine was stuck at step 11 out of 16 . I hope with the height sensors installed it's good
Mine was stuck at step 11 out of 16 . I hope with the height sensors installed it's good
Try to reset your manifold. To reset your manifold, simply unplug the main harness for five minutes and plug it back in after five minutes. I got this advice from Bagriders. If that fails then you need to relocate your sensors. Do you have photos of where you mount your sensors and your rods too? I would want an idea where it is.
Try to reset your manifold. To reset your manifold, simply unplug the main harness for five minutes and plug it back in after five minutes. I got this advice from Bagriders. If that fails then you need to relocate your sensors. Do you have photos of where you mount your sensors and your rods too? I would want an idea where it is.