Excelerate Performance: INGALLS Engine Torque Damper Groupbuy!!!
07-29-2010, 11:33 AM
#42
yes you can order just the bracket. I posted the link for it 2 posts up.
http://www.ingallseng.com/product.php?productid=20810
http://www.ingallseng.com/product.php?productid=20810
07-29-2010, 02:41 PM
#44
Whats up with RDX owners?
iTrader: (9)
The Ingalls setup is better simply because it has the most leverage on the motor.
Pretend you have a pole thats wobbling in the wind, if you grab the bottom (NRG dampeners in stock location) you may slow it down, but its not stopping the swaying motion. If you grab the top though (Ingalls dampener location), its going to slow it down much more.
07-30-2010, 01:34 PM
#50
Whats up with RDX owners?
iTrader: (9)
Where did you order it?
07-30-2010, 03:04 PM
#51
Mine is also on the truck today, just waiting for it to get here. I ordered through Corsport USA and it was shipped directly from ingalls, im sure he did the same, or just ordered direct. I had no idea how long the GB would take so i paid the extra to have it now.
07-30-2010, 05:06 PM
#55
Suzuka Master
iTrader: (1)
So, what's your overall impression thus far? (I realize you just installed it and it may be a little premature.) Interested in some feedback at your earliest convenience.
It looks like you have a blower. I do as well. I'm looking hard at this mod since I just put new front and rear mounts on when I performed the TB procedure. If this can extend their life a little I may put it on the agenda.
Thanks.
It looks like you have a blower. I do as well. I'm looking hard at this mod since I just put new front and rear mounts on when I performed the TB procedure. If this can extend their life a little I may put it on the agenda.
Thanks.
07-30-2010, 05:46 PM
#57
Whats up with RDX owners?
iTrader: (9)
The NRG wont disappear as long as you use thread tape on bolts (the same tape you use for plumbing stuff). Ive got over 40k miles on them and they havent gone anywhere.
07-31-2010, 12:48 PM
#60
Whats up with RDX owners?
iTrader: (9)
No you dont need a spacer for the stock bar. The stock bar is nowhere near as stiff as the Cusco/CT/Neuspeed bars.
07-31-2010, 09:24 PM
#63
In regards to the CT Strut bar and pictures see below:
Yes, the kit was proto-typed on a CL with the Comptech titanium strut bar brace so there should be no problems with that. The Comptech STB makes it a bit more difficult to install, because the ends are fixed and the strut bolts are angled in. Also, with the Comptech STB, they may want to purchase another strut tower bracket to space up the driver's side so the bar remains level and fits properly. The bracket could be trimmed down to just a spacer. That is what we ended up doing on our test vehicle. We do not have any untrimmed strut brackets at this time, unless demand warrants them.
You can see the pictures of the install with the Comptech STB in the instructions here:
http://www.ingallseng.com/Instructions/93055.pdf
Yes, the kit was proto-typed on a CL with the Comptech titanium strut bar brace so there should be no problems with that. The Comptech STB makes it a bit more difficult to install, because the ends are fixed and the strut bolts are angled in. Also, with the Comptech STB, they may want to purchase another strut tower bracket to space up the driver's side so the bar remains level and fits properly. The bracket could be trimmed down to just a spacer. That is what we ended up doing on our test vehicle. We do not have any untrimmed strut brackets at this time, unless demand warrants them.
You can see the pictures of the install with the Comptech STB in the instructions here:
http://www.ingallseng.com/Instructions/93055.pdf
, it was a TL FYI and don't even bother trying to argue that
07-31-2010, 09:29 PM
#64
Mine is also on the truck today, just waiting for it to get here. I ordered through Corsport USA and it was shipped directly from ingalls, im sure he did the same, or just ordered direct. I had no idea how long the GB would take so i paid the extra to have it now.
07-31-2010, 09:51 PM
#65
Whats up with RDX owners?
iTrader: (9)
(and as mentioned over past month's; black is a f***er to keep clean, but looks the best when it is clean though), gfrg88's is WDP though (also here in Denver)
08-01-2010, 04:28 AM
#67
I was talking about not wanting to wait around for the group buy through excelerate. I purchased through corsport because ordering it through them was cheaper than getting it direct from ingalls. I didn't know corsport wasnt the one shipping until the owner told me.
08-01-2010, 10:10 PM
#68
Whats up with RDX owners?
iTrader: (9)
08-05-2010, 02:12 PM
#71
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
^^^ will this fit the 3G TL ?
)
08-06-2010, 03:07 AM
#73
Whats up with RDX owners?
iTrader: (9)
Doesnt Ingalls make one for the 3rd gen?
BTW, just checked my other email acct and I saw that it should be here tomorrow
BTW, just checked my other email acct and I saw that it should be here tomorrow
08-06-2010, 02:14 PM
#76
I just talked to Josh, the owner, on the phone.
He also said if we want to get another 20 people we could do the group buy again.
He also said if we want to get another 20 people we could do the group buy again.
08-06-2010, 02:55 PM
#77
Hi,
The group buy just ended for the Ingalls torque damper.
If anyone's interested, I just talked to Josh, the owner, on the phone.
He also said if we want to get another 20 people we could do the group buy again.
I can keep a tab and contact him when we get enough people.
1)thelastaspec
The group buy just ended for the Ingalls torque damper.
If anyone's interested, I just talked to Josh, the owner, on the phone.
He also said if we want to get another 20 people we could do the group buy again.
I can keep a tab and contact him when we get enough people.
1)thelastaspec
08-06-2010, 03:09 PM
#78
Whats up with RDX owners?
iTrader: (9)
Just arrived. Ill install it later tonight.
08-06-2010, 03:36 PM
#79
Mine just arrived and I went to my shop earlier today to have him cut the extra part of my extra bracket to make it a spacer. He did it for free, nice of him.
Last edited by 97BlackAckCL; 08-07-2010 at 11:42 AM.
08-06-2010, 05:50 PM
#80
We already have an Engine Damper for the 3rd gen TL:
http://store.excelerateperformance.c.../i-300876.aspx
http://store.excelerateperformance.c.../i-300876.aspx