AcuraZine - Acura Enthusiast Community
0 2019/03/09 13:24:51
Looks good
Looks good
0 2019/03/09 13:24:43
0 2019/03/09 13:24:36
Bought brake fluid and power steering fluid to change in both TLs and the MDX.
Bought brake fluid and power steering fluid to change in both TLs and the MDX.
0 2019/03/09 13:24:26
Looks good there
Looks good there
0 2019/03/09 13:24:18
Reinstallarion of bladder successful
Reinstallarion of bladder successful
0 2019/03/09 13:24:09
Cleaned up the windshield wiper bladder.
Cleaned up the windshield wiper bladder.
0 2019/03/09 13:24:00
0 2019/03/09 13:21:52
0 2019/03/09 13:21:43
0 2019/03/09 13:21:35
0 2019/03/09 13:21:27
0 2019/03/09 13:21:18
0 2019/03/09 13:21:10
0 2019/03/09 13:21:00
0 2019/03/09 13:20:51
0 2019/03/09 13:20:41
ya
ya
0 2019/03/09 13:20:32
The interior of the front bumpers needed to be trimmed to make room for the new intercooler charge pipes.
The interior of the front bumpers needed to be trimmed to make room for the new intercooler charge pipes.
0 2019/03/09 13:20:22
The Evap sensor was deleted due to it no longer being used.
The Evap sensor was deleted due to it no longer being used.
0 2019/03/09 13:13:21
There is the Evap sensor which the front and rear engine mounts are connected to. I deleted the hydraulic vacuum lines.
There is the Evap sensor which the front and rear engine mounts are connected to. I deleted the hydraulic vacuum lines.
0 2019/03/09 13:13:14
I ended up cutting the bottom of the fuel cage to seat the o-ring that delivers fuel.
I ended up cutting the bottom of the fuel cage to seat the o-ring that delivers fuel.
0 2019/03/09 13:13:08
0 2019/03/09 13:12:59
The fuel pump sock was bottoming out on the bottom of the fuel cage.
The fuel pump sock was bottoming out on the bottom of the fuel cage.
0 2019/03/09 13:12:51
0 2019/03/09 13:12:43
x2 One-way check valves are used to prevent boost from escaping from the intake manifold. When not in boost, the check valve allows vacuum to flow once again.
x2 One-way check valves are used to prevent boost from escaping from the intake manifold. When not in boost, the check valve allows vacuum to flow once again.
0 2019/03/09 13:08:13
Nothing to it.
Nothing to it.
0 2019/03/09 13:08:05
0 2019/03/09 13:07:55
0 2019/03/09 13:07:45
Everything reinstalled.
Everything reinstalled.
0 2019/03/09 13:07:36
Test fitting the new longer serpentine belt around the Rotrex pulley.
Test fitting the new longer serpentine belt around the Rotrex pulley.
0 2019/03/09 13:02:46
Ins
Ins
0 2019/03/09 13:02:37
The 4” intake pipe which is connected to the Rotrex unit is in close proximity to the anterior RV6 v3 PCD exhaust pipe. Thoughtfully, Andy Gerzina over at Gerzy Bear Performance provided an 1800F heat shield to keep the intake temperatures down.
The 4” intake pipe which is connected to the Rotrex unit is in close proximity to the anterior RV6 v3 PCD exhaust pipe. Thoughtfully, Andy Gerzina over at Gerzy Bear Performance provided an 1800F heat shield to keep the intake temperatures down.
0 2019/03/09 13:02:29
New P2P intake manifold hex studs.
New P2P intake manifold hex studs.
0 2019/03/09 13:02:19
0 2019/03/09 12:58:44
Cat approved of Intake manifold fitment.
Cat approved of Intake manifold fitment.
0 2019/03/09 12:58:36
Use bolts clear the gap. Should hold?
Use bolts clear the gap. Should hold?
0 2019/03/09 12:58:27
Rear engine mount installed! Not easy to install,but I refrained from reinstalling anything back there to give me more room. It is still more difficult to get the oem one out.
Rear engine mount installed! Not easy to install,but I refrained from reinstalling anything back there to give me more room. It is still more difficult to get the oem one out.
0 2019/03/09 12:58:18
Gap between the two parts of the mount.
Gap between the two parts of the mount.
0 2019/03/09 12:58:11
Testing new serpentine belt
Testing new serpentine belt
0 2019/03/09 12:49:27
One-way check valves are to be installed to prevent boost from out of the intake manifold via pipes connected to it. Boost should only be going through the vacuum lines which feed to the Fuel regulator, Blow off valve, Wastegate.
One-way check valves are to be installed to prevent boost from out of the intake manifold via pipes connected to it. Boost should only be going through the vacuum lines which feed to the Fuel regulator, Blow off valve, Wastegate.
0 2019/03/09 12:49:19