AcuraZine - Acura Enthusiast Community
Use a smaller flathead screwdriver to gently remove the two clips.
Use a smaller flathead screwdriver to gently remove the two clips.
0 2019/05/23 22:06:11
0 2019/05/23 22:06:10
Remove these two bolts to get the wiring off and out of the way of tranny.
Remove these two bolts to get the wiring off and out of the way of tranny.
0 2019/05/23 22:06:09
0 2019/05/23 22:06:07
The tranny does not weigh much. One person can Easily remove it. comes off like butter. Make sure to place a jack of some sort under the tranny for the first inch or so. You will then have the spline rod holding on the engine, and the other end resting safely on the subfame.
The tranny does not weigh much. One person can Easily remove it. comes off like butter. Make sure to place a jack of some sort under the tranny for the first inch or so. You will then have the spline rod holding on the engine, and the other end resting safely on the subfame.
0 2019/05/23 22:06:06
Passenger side axle removed.
Passenger side axle removed.
0 2019/05/23 22:06:05
Clutch line out of the way. Tranny is ready to be removed.
Clutch line out of the way. Tranny is ready to be removed.
0 2019/05/23 22:06:03
remove the clutch line with a 10 socket and move the line out of the way. You don't want it breaking when you move the tranny out of the way.
remove the clutch line with a 10 socket and move the line out of the way. You don't want it breaking when you move the tranny out of the way.
0 2019/05/23 22:06:02
The driver side axle has a clip that must be taken out with care. you don't want this breaking inside the trannys differential. If you apply pressure to remove the axle at the base of the tranny and it doesn't go, try turning it a hair and keep trying until it pops.
The driver side axle has a clip that must be taken out with care. you don't want this breaking inside the trannys differential. If you apply pressure to remove the axle at the base of the tranny and it doesn't go, try turning it a hair and keep trying until it pops.
0 2019/05/23 22:06:01
Here is the intermediate shaft bolt pattern. It is connected to the passenger axle.
Here is the intermediate shaft bolt pattern. It is connected to the passenger axle.
0 2019/05/23 22:05:59
Pointer points at the same bolt in the anterior part of the engine. This bolt goes from engine to tranny. To get to this bolt you must remove the part of the front mount that goes from the front mount to the engine. There are a total of x5 bolts to remove this bracket.
Pointer points at the same bolt in the anterior part of the engine. This bolt goes from engine to tranny. To get to this bolt you must remove the part of the front mount that goes from the front mount to the engine. There are a total of x5 bolts to remove this bracket.
0 2019/05/23 22:05:58
My pointer shows a sneaky bolt that goes from the rear of the engine into the tranny.
My pointer shows a sneaky bolt that goes from the rear of the engine into the tranny.
0 2019/05/23 22:05:57
The intermediate shaft has no clip on the spline, so removal is easy, just pull at the base at the tranny. But do not pull on the axle itself, it may ruin it.
The intermediate shaft has no clip on the spline, so removal is easy, just pull at the base at the tranny. But do not pull on the axle itself, it may ruin it.
0 2019/05/23 22:05:55
Heres what the rear of the engine should look like with the x3 bolts of the black intermediate shaft heatshield should look like. Then remove the x3 bolts that hold the internediate shaft in place. The top bolt will be tricky. Use a a wrench with a smaller handle.
Heres what the rear of the engine should look like with the x3 bolts of the black intermediate shaft heatshield should look like. Then remove the x3 bolts that hold the internediate shaft in place. The top bolt will be tricky. Use a a wrench with a smaller handle.
0 2019/05/23 22:05:54
Easy access to the shaft. Start by removing the bracket that holds the rear pre-cat in place.
Easy access to the shaft. Start by removing the bracket that holds the rear pre-cat in place.
0 2019/05/23 22:05:52
0 2019/05/23 22:05:51
0 2019/05/23 22:05:50
Removed the ATLP J-Pipe, not the intermediate shaft is ready to come off. I popped the remaining Exhaust pipe with a tire prop.
Removed the ATLP J-Pipe, not the intermediate shaft is ready to come off. I popped the remaining Exhaust pipe with a tire prop.
0 2019/05/23 22:05:49
0 2019/05/23 22:03:33
0 2019/05/23 22:03:32
0 2019/05/23 22:03:31
0 2019/05/22 19:42:57
0 2019/05/22 19:42:48
0 2019/05/22 19:42:40
0 2019/05/22 19:42:31
0 2019/05/22 19:42:24
Tranny mounts removed.
Tranny mounts removed.
0 2019/05/22 19:42:14
Tranny propped with Jack.
Tranny propped with Jack.
0 2019/05/22 19:42:05
Tranny propped with Jack.
Tranny propped with Jack.
0 2019/05/22 19:40:53
Tranny mounts removed.
Tranny mounts removed.
0 2019/05/22 19:40:44
0 2019/05/22 19:40:35
0 2019/05/22 06:49:54
I borrowed a ball joint separator from Vatozone today. It didn’t work at all. Slipped off quite violently on my last go at it.
I borrowed a ball joint separator from Vatozone today. It didn’t work at all. Slipped off quite violently on my last go at it.
0 2019/05/21 19:34:09
Im a bit puzzled as to how to safely remove the axles. I turned and pulled in different
Im a bit puzzled as to how to safely remove the axles. I turned and pulled in different
0 2019/05/21 19:34:00
EricTheCarGuy has videos for an Acura TL engine replacement. In it he shows that the axles can be removed by removing the x2 medial bolts of the control arm. I did just that and it took 2 minutes for each side. H’like a glove!
EricTheCarGuy has videos for an Acura TL engine replacement. In it he shows that the axles can be removed by removing the x2 medial bolts of the control arm. I did just that and it took 2 minutes for each side. H’like a glove!
0 2019/05/21 19:33:52
0 2019/05/21 06:07:20
I’m having a difficult time removing the lower arm to free the axle. I’ve removed the pin and nut. On YouTube it looks like it slides right out. Should I buy a tool with more leverage? Help me Fellas!
I’m having a difficult time removing the lower arm to free the axle. I’ve removed the pin and nut. On YouTube it looks like it slides right out. Should I buy a tool with more leverage? Help me Fellas!
0 2019/05/21 06:06:52
Vatozone loans out tools, so I got the 36mm socket and redneck slaphammer to remove the axles.
Vatozone loans out tools, so I got the 36mm socket and redneck slaphammer to remove the axles.
0 2019/05/21 06:04:11
Got stuck at the axlenut..
Got stuck at the axlenut..
0 2019/05/21 06:03:49
Put her on jacks for easy access underneath.
Put her on jacks for easy access underneath.
0 2019/05/21 06:03:18