AcuraZine - Acura Enthusiast Community
One-way check valves are to be installed to prevent boost from out of the intake manifold via pipes connected to it. Boost should only be going through the vacuum lines which feed to the Fuel regulator, Blow off valve, Wastegate.
One-way check valves are to be installed to prevent boost from out of the intake manifold via pipes connected to it. Boost should only be going through the vacuum lines which feed to the Fuel regulator, Blow off valve, Wastegate.
0 2019/03/09 12:49:19
I’m order to secure the Rotrex bracket, you must temporarily remove the alternator. Do this by removing the #12 bolt and the green bracket.
I’m order to secure the Rotrex bracket, you must temporarily remove the alternator. Do this by removing the #12 bolt and the green bracket.
0 2019/01/01 21:22:07
Gap between the two parts of the mount.
Gap between the two parts of the mount.
0 2019/03/09 12:58:11
Testing new serpentine belt
Testing new serpentine belt
0 2019/03/09 12:49:27
Also remove this #10 bolt and move the wiring harness to Towards the power steering reservoir.
Also remove this #10 bolt and move the wiring harness to Towards the power steering reservoir.
0 2019/01/01 21:22:08
Rear engine mount installed! Not easy to install,but I refrained from reinstalling anything back there to give me more room. It is still more difficult to get the oem one out.
Rear engine mount installed! Not easy to install,but I refrained from reinstalling anything back there to give me more room. It is still more difficult to get the oem one out.
0 2019/03/09 12:58:18
Remove this bolt on the left of the alternator.
Remove this bolt on the left of the alternator.
0 2019/01/01 21:22:09
Use bolts clear the gap. Should hold?
Use bolts clear the gap. Should hold?
0 2019/03/09 12:58:27
I would suggest to take the bracket with the circle off until you install the Rotrex onto it.
I would suggest to take the bracket with the circle off until you install the Rotrex onto it.
0 2019/01/01 21:22:10
Cat approved of Intake manifold fitment.
Cat approved of Intake manifold fitment.
0 2019/03/09 12:58:36
Here it is!!
Here it is!!
0 2019/01/01 21:22:10
0 2019/03/09 12:58:44
0 2019/01/01 21:29:01
New P2P intake manifold hex studs.
New P2P intake manifold hex studs.
0 2019/03/09 13:02:19
Rein
Rein
0 2019/01/01 21:29:02
The 4” intake pipe which is connected to the Rotrex unit is in close proximity to the anterior RV6 v3 PCD exhaust pipe. Thoughtfully, Andy Gerzina over at Gerzy Bear Performance provided an 1800F heat shield to keep the intake temperatures down.
The 4” intake pipe which is connected to the Rotrex unit is in close proximity to the anterior RV6 v3 PCD exhaust pipe. Thoughtfully, Andy Gerzina over at Gerzy Bear Performance provided an 1800F heat shield to keep the intake temperatures down.
0 2019/03/09 13:02:29
Don’t forget the spacer!
Don’t forget the spacer!
0 2019/01/01 21:31:01
Ins
Ins
0 2019/03/09 13:02:37
Starting to put the Rotrex coolant lines into the Rotrex. As usual, work from the inside out.
Starting to put the Rotrex coolant lines into the Rotrex. As usual, work from the inside out.
0 2019/01/01 21:31:02
Test fitting the new longer serpentine belt around the Rotrex pulley.
Test fitting the new longer serpentine belt around the Rotrex pulley.
0 2019/03/09 13:02:46
Had to raise the engine to get the Rotrex unit to sit flush on the nracket.
Had to raise the engine to get the Rotrex unit to sit flush on the nracket.
0 2019/01/01 21:31:04
Everything reinstalled.
Everything reinstalled.
0 2019/03/09 13:07:36
Now with the Rotrex unit in place, it’s time to test fit the first first charge pipe!!
Now with the Rotrex unit in place, it’s time to test fit the first first charge pipe!!
0 2019/01/01 21:31:05
0 2019/03/09 13:07:45
Reinstall the alternator, take the Special long bolt from the bolt supply and put it into the hinge joint between the Rotrex and alternator.
Reinstall the alternator, take the Special long bolt from the bolt supply and put it into the hinge joint between the Rotrex and alternator.
0 2019/01/01 21:31:05
0 2019/03/09 13:07:55
Secure the banjo bolt and hose clamp at this angle. It will keep that charge pipe from rubbing them.
Secure the banjo bolt and hose clamp at this angle. It will keep that charge pipe from rubbing them.
0 2019/01/01 21:38:22
Nothing to it.
Nothing to it.
0 2019/03/09 13:08:05
Reinstall the power steering radiator to its original location. First bend the the two brackets towards the car.
Reinstall the power steering radiator to its original location. First bend the the two brackets towards the car.
0 2019/01/01 21:38:22
x2 One-way check valves are used to prevent boost from escaping from the intake manifold. When not in boost, the check valve allows vacuum to flow once again.
x2 One-way check valves are used to prevent boost from escaping from the intake manifold. When not in boost, the check valve allows vacuum to flow once again.
0 2019/03/09 13:08:13
The power steering radiator must look recessed like so.
The power steering radiator must look recessed like so.
0 2019/01/01 21:38:23
0 2019/03/09 13:12:43
Beautiful! Strap down the intercooler and begin assembling the charge piping
Beautiful! Strap down the intercooler and begin assembling the charge piping
0 2019/01/01 21:38:32
0 2019/01/01 21:45:59
The fuel pump sock was bottoming out on the bottom of the fuel cage.
The fuel pump sock was bottoming out on the bottom of the fuel cage.
0 2019/03/09 13:12:51
0 2019/01/01 21:46:02
0 2019/03/09 13:12:59
0 2019/01/01 21:46:03
I ended up cutting the bottom of the fuel cage to seat the o-ring that delivers fuel.
I ended up cutting the bottom of the fuel cage to seat the o-ring that delivers fuel.
0 2019/03/09 13:13:08
Tightened the first coupling. I placed the clamps in this position to keep them away from the motor radiator and ease of access.
Tightened the first coupling. I placed the clamps in this position to keep them away from the motor radiator and ease of access.
0 2019/01/01 21:46:53