We just got our shipment of TAKEDA intakes!!!
09-15-2009, 12:27 AM
#121
No, you are wrong. All I have to do is look at the Takeda Intake and see the hole where you disconnect the factory MAF sensor to put it into the new intake to know that the TL has a MAF sensor. MAP sensors are for older Acura/Hondas
09-18-2009, 11:13 AM
#123
1st Gear
Join Date: Sep 2009
Age: 55
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
First time poster.
I'm glad I checked out this site. I've been wanting to up the HP a little on my 09 AWD and looks like I've found the right place.
I have a history building up GM engines and did some tuning on a LS1 I owned, first with LS1 Edit and then with HP Tuners when they started out.
The ECU shouldn't have to make much of an adjustment for an intake since it's still accurately measuring airflow into the engine. If you were to modify the MAF I could see the increase diminish fairly rapidly but that's not the case. In the LS world we saw this happen with ported MAFs. When first installed the extra unmeasured airflow leaned the engine and the ECU would try to compensate and eventually would adjust and return the AF back to normal. We could see this happen with the L-trims (Long term AF trim). We did not see any performance gain lost when swapping out the air lid which is equivalent to the air intake in this case. I would tune the AF with the ported ends installed and set the target AF leaner for more HP so the ECU wouldn't try and trim the AF richer. I also used a wide-band O2 so I could tune WOT.
Just thought I should share...
I'm glad I checked out this site. I've been wanting to up the HP a little on my 09 AWD and looks like I've found the right place.
I have a history building up GM engines and did some tuning on a LS1 I owned, first with LS1 Edit and then with HP Tuners when they started out.
The ECU shouldn't have to make much of an adjustment for an intake since it's still accurately measuring airflow into the engine. If you were to modify the MAF I could see the increase diminish fairly rapidly but that's not the case. In the LS world we saw this happen with ported MAFs. When first installed the extra unmeasured airflow leaned the engine and the ECU would try to compensate and eventually would adjust and return the AF back to normal. We could see this happen with the L-trims (Long term AF trim). We did not see any performance gain lost when swapping out the air lid which is equivalent to the air intake in this case. I would tune the AF with the ported ends installed and set the target AF leaner for more HP so the ECU wouldn't try and trim the AF richer. I also used a wide-band O2 so I could tune WOT.
Just thought I should share...
09-18-2009, 07:44 PM
#124
10th Gear
Join Date: Sep 2009
Age: 58
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
What does the intake do to your gas mileage? I wanted an MDX but the wifey wanted better gas mileage. I told her that I would "suffer" and get the TL SH-AWD. I don't tell her I am probably getting worse mileage because I can't keep the peddle off the floor. 
09-21-2009, 09:54 AM
#125
Three Wheelin'
Just installed my takeda and I must say the instructions could have been a bit better. It would have been nice if the instructions had said remove, "metal coolant line". I did not realize this until near the end of the install. Cold have saved 30min of time. I also recommend that you use a screwdriver to help "Push" the hoses off.
As been already said, the sound is nice. Adds a bit of excitement to the driving experience.
Hard for me to say if there is any HP improvement since I have very little seat time in my TL. It does appear my gas mileage has improved. I like the fact that normal driving the car is still very quit. I had some concerns there.
As been already said, the sound is nice. Adds a bit of excitement to the driving experience.
Hard for me to say if there is any HP improvement since I have very little seat time in my TL. It does appear my gas mileage has improved. I like the fact that normal driving the car is still very quit. I had some concerns there.
09-24-2009, 02:12 PM
#127
After reading four pages of favorable reviews for the Takeda intake, it's hard to resist not having one! If I get one, I'll have to install it in the middle of the night since my wife would kill me modding a perfectly fine car...ha
09-24-2009, 05:35 PM
#128
Three Wheelin'
You better have a good flashlight!
09-27-2009, 06:07 PM
#129
Advanced
Join Date: Feb 2006
Location: BC, Canada
Age: 38
Posts: 87
Likes: 0
Received 0 Likes
on
0 Posts
can anyone post up another video of what the intake sounds like? I tried watching the video of the dyno run, but it had been pulled down. Preferably on the 3.7L motor
09-27-2009, 07:07 PM
#130
Pro
09-27-2009, 10:25 PM
#131
Three Wheelin'
09-28-2009, 11:00 AM
#133
does anyone know if this puppy will fit 09 RL? I'm assuming the engine and most other things are the same as AWD TL...
https://acurazine.com/forums/2g-rl-2005-2012-76/would-4g-tl-intake-fit-2-5g-rl-744650/
thread above shows my photos (and frustration) when trying to mount an 08 TL intake...it was missing a spot for a huge sensor...
anyway, any help is appreciated
https://acurazine.com/forums/2g-rl-2005-2012-76/would-4g-tl-intake-fit-2-5g-rl-744650/
thread above shows my photos (and frustration) when trying to mount an 08 TL intake...it was missing a spot for a huge sensor...
anyway, any help is appreciated
Last edited by 037; 09-28-2009 at 11:03 AM.
09-28-2009, 01:01 PM
#134
Three Wheelin'
does anyone know if this puppy will fit 09 RL? I'm assuming the engine and most other things are the same as AWD TL...
https://acurazine.com/forums/showthread.php?t=744650
thread above shows my photos (and frustration) when trying to mount an 08 TL intake...it was missing a spot for a huge sensor...
anyway, any help is appreciated
https://acurazine.com/forums/showthread.php?t=744650
thread above shows my photos (and frustration) when trying to mount an 08 TL intake...it was missing a spot for a huge sensor...
anyway, any help is appreciated
09-28-2009, 03:54 PM
#135
09-28-2009, 04:39 PM
#136
I am a bullet proof tiger
09-29-2009, 10:55 AM
#137
09-29-2009, 06:39 PM
#139
Installed my intake this past weekend ('09 SH-AWD). Car feels slightly different off the line, but absolutely has more pep at highway speeds.
While idling and tooling around town, the car doesn't sound all that much different while driving, when you get on the pedal though, wow, what a difference. The engine sounds much more pronounced and has a definite growl.
Not sure how it has affected gas mileage yet.
While idling and tooling around town, the car doesn't sound all that much different while driving, when you get on the pedal though, wow, what a difference. The engine sounds much more pronounced and has a definite growl.
Not sure how it has affected gas mileage yet.
09-29-2009, 06:49 PM
#140
who did you order from, how much, any special instructions?
was it a direct fit?
I definitely want to know about the gas consumption as my RL is giving me low teens in NY driving...
was it a direct fit?
I definitely want to know about the gas consumption as my RL is giving me low teens in NY driving...
09-29-2009, 09:04 PM
#141
I got it from excelerateperformance.com (the thread starter).
No special instructions--the ones included with the kit are basically perfect. And yes, it was a direct fit. It included the correct adapter for the 3.7 in the SH-AWD.
No special instructions--the ones included with the kit are basically perfect. And yes, it was a direct fit. It included the correct adapter for the 3.7 in the SH-AWD.
10-01-2009, 05:16 PM
#146
I am a bullet proof tiger
10-01-2009, 05:39 PM
#148
lol.. i couldnt wait for Comptech... they said its already been designed , but they gave me no ETA on production.. not even a ballpark... so i gave up.. i could always sell the Takeda if i like the ct-engineering design more
I also got the P2R TB & IM Spacers today & UR Pulley coming soon
I also got the P2R TB & IM Spacers today & UR Pulley coming soon
10-01-2009, 11:35 PM
#152
^ Josh @ Excelerate
just installed everything... ya know, i laughed at the original dyno, that shows 14whp/wtq gain.... honestly, its not that far off!! i feel MASSIVE low-end gains
Just a Question-
Does everybody else have the intake whistle sound? both my 3Gs had it... i just wanted to make sure i tighten the TB spacer enough, and all clamps are tightened properly
just installed everything... ya know, i laughed at the original dyno, that shows 14whp/wtq gain.... honestly, its not that far off!! i feel MASSIVE low-end gains
Just a Question-
Does everybody else have the intake whistle sound? both my 3Gs had it... i just wanted to make sure i tighten the TB spacer enough, and all clamps are tightened properly
10-02-2009, 09:27 AM
#154
^ Josh @ Excelerate
just installed everything... ya know, i laughed at the original dyno, that shows 14whp/wtq gain.... honestly, its not that far off!! i feel MASSIVE low-end gains
Just a Question-
Does everybody else have the intake whistle sound? both my 3Gs had it... i just wanted to make sure i tighten the TB spacer enough, and all clamps are tightened properly
just installed everything... ya know, i laughed at the original dyno, that shows 14whp/wtq gain.... honestly, its not that far off!! i feel MASSIVE low-end gains
Just a Question-
Does everybody else have the intake whistle sound? both my 3Gs had it... i just wanted to make sure i tighten the TB spacer enough, and all clamps are tightened properly
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
10-02-2009, 09:44 AM
#155
Three Wheelin'
I just got my intake last night and I plan on installing it tomorrow. In the packaging included in the two hoses (5/8" and 5/16") bag I notice an 8" piece of rubber in the shape of a 'U". After reading the installation instruction I didn't see where is piece comes into play. Any thoughts?
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
I wonder about the spacer too.
10-02-2009, 09:48 AM
#156
Just installed my takeda and I must say the instructions could have been a bit better. It would have been nice if the instructions had said remove, "metal coolant line". I did not realize this until near the end of the install. Cold have saved 30min of time. I also recommend that you use a screwdriver to help "Push" the hoses off.
As been already said, the sound is nice. Adds a bit of excitement to the driving experience.
Hard for me to say if there is any HP improvement since I have very little seat time in my TL. It does appear my gas mileage has improved. I like the fact that normal driving the car is still very quit. I had some concerns there.
As been already said, the sound is nice. Adds a bit of excitement to the driving experience.
Hard for me to say if there is any HP improvement since I have very little seat time in my TL. It does appear my gas mileage has improved. I like the fact that normal driving the car is still very quit. I had some concerns there.
-Travis
Last edited by lewisvilleTL; 10-02-2009 at 09:51 AM.
10-02-2009, 10:25 AM
#157
I am a bullet proof tiger
^ Josh @ Excelerate
just installed everything... ya know, i laughed at the original dyno, that shows 14whp/wtq gain.... honestly, its not that far off!! i feel MASSIVE low-end gains
Just a Question-
Does everybody else have the intake whistle sound? both my 3Gs had it... i just wanted to make sure i tighten the TB spacer enough, and all clamps are tightened properly
just installed everything... ya know, i laughed at the original dyno, that shows 14whp/wtq gain.... honestly, its not that far off!! i feel MASSIVE low-end gains
Just a Question-
Does everybody else have the intake whistle sound? both my 3Gs had it... i just wanted to make sure i tighten the TB spacer enough, and all clamps are tightened properly
10-02-2009, 12:19 PM
#158
Instructor
Join Date: Jun 2009
Location: Egg Harbor Twp, NJ
Age: 41
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
I just got my intake last night and I plan on installing it tomorrow. In the packaging included in the two hoses (5/8" and 5/16") bag I notice an 8" piece of rubber in the shape of a 'U". After reading the installation instruction I didn't see where is piece comes into play. Any thoughts?
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
In my Z, the spacer was the best dollar-per-hp gain mod I ever did. Doing it at the same time as an intake is smart though.
10-02-2009, 12:41 PM
#159
I just got my intake last night and I plan on installing it tomorrow. In the packaging included in the two hoses (5/8" and 5/16") bag I notice an 8" piece of rubber in the shape of a 'U". After reading the installation instruction I didn't see where is piece comes into play. Any thoughts?
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
So I wonder how each performance part did exclusively for you? I'm hesitant about the TB spacer. I don't understand how a 3/4" piece of metal could REALLY increase hp, tq and fuel economy. What are your thoughts?
-Travis
I would wager the majority of what Blackura is feeling is the spacer, but I can't say for sure as I'm not as familiar with how this engine responds to mods.
In my Z, the spacer was the best dollar-per-hp gain mod I ever did. Doing it at the same time as an intake is smart though.
In my Z, the spacer was the best dollar-per-hp gain mod I ever did. Doing it at the same time as an intake is smart though.
