AcuraZine - Acura Enthusiast Community
0 2021/06/03 00:14:58
Alright fellas, no more messing around. It’s time to do the real part of the surgery.
Alright fellas, no more messing around. It’s time to do the real part of the surgery.
0 2021/06/03 07:26:51
0 2021/06/03 07:26:59
Haven’t seen a clutch so worn out before. ...Though I’ve only replaced a couple. But those clutch disks were spinning and had more met on them, but the cars were not stock.
Haven’t seen a clutch so worn out before. ...Though I’ve only replaced a couple. But those clutch disks were spinning and had more met on them, but the cars were not stock.
0 2021/06/03 07:43:07
I’d say it was time to change the clutch disk.
I’d say it was time to change the clutch disk.
0 2021/06/03 09:18:18
0 2021/06/03 22:44:28
0 2021/06/03 22:44:36
0 2021/06/03 22:44:43
0 2021/06/03 22:51:36
0 2021/06/05 11:07:44
I have here an MP90 from 1991 Mustang/Camaro. It’s says 3.8 on the bottom on the underbelly. It’s very compact but the bolt pattern is the similar to the Eaton M90 Gen 3. A custom plate would have to be made
I have here an MP90 from 1991 Mustang/Camaro. It’s says 3.8 on the bottom on the underbelly. It’s very compact but the bolt pattern is the similar to the Eaton M90 Gen 3. A custom plate would have to be made
0 2021/06/05 11:07:50
0 2021/06/05 11:07:56
0 2021/06/05 11:08:03
0 2021/06/05 11:08:11
Changed rear cam seal
Changed rear cam seal
0 2021/06/05 22:43:26
Changed rear mount
Changed rear mount
0 2021/06/05 22:43:31
Took a bit to get the rear mount hydronic tube back on. If you go under the car and remove the 12mm bolt securing the tube, you will get enough slack to easily resecure it.
Took a bit to get the rear mount hydronic tube back on. If you go under the car and remove the 12mm bolt securing the tube, you will get enough slack to easily resecure it.
0 2021/06/05 22:43:37
Began cleaning the engine bay as the only seals that may still leak is the oil pump housing. I’m going to mate the trans and engine back together tomorrow, then begin reassembly.
Began cleaning the engine bay as the only seals that may still leak is the oil pump housing. I’m going to mate the trans and engine back together tomorrow, then begin reassembly.
0 2021/06/05 22:43:46
0 2021/06/06 22:06:59
Tomatoes are coming in nice 👍
Tomatoes are coming in nice 👍
0 2021/06/06 22:08:06
0 2021/06/06 22:12:41
0 2021/06/07 21:58:48
0 2021/06/07 21:58:58
0 2021/06/07 21:59:06
0 2021/06/07 21:59:15
Use only original fellers!
Use only original fellers!
0 2021/06/07 22:01:35
0 2021/06/07 22:01:45
0 2021/06/07 22:01:54
0 2021/06/07 22:02:02
Heeltoe TSX, Woop-Woop!
Heeltoe TSX, Woop-Woop!
0 2021/06/07 23:01:03
Picked up that good-good(And none of that bad-bad).
Picked up that good-good(And none of that bad-bad).
0 2021/06/07 23:01:17
0 2021/06/08 10:36:55
0 2021/06/08 10:37:08
0 2021/06/08 10:37:18
Pulled these straight from my garden. Six sprinkler heads are dedicated just for the garden area so they grow maintainence free.
Pulled these straight from my garden. Six sprinkler heads are dedicated just for the garden area so they grow maintainence free.
0 2021/06/09 19:27:13
If you compare Chito Simmons Comptech M90 that he may never install, yet won’t sell. You will see it’s exactly like my M90z
If you compare Chito Simmons Comptech M90 that he may never install, yet won’t sell. You will see it’s exactly like my M90z
0 2021/06/26 22:04:42
This means I can take my NIB Comptech snout and use my new Weldprime Tog welder to make a Comptech M90 without modifying my MP62 Comptech.
This means I can take my NIB Comptech snout and use my new Weldprime Tog welder to make a Comptech M90 without modifying my MP62 Comptech.
0 2021/06/26 22:05:20
Building an M90 Comptech from scratch like this will kill three birds with one stone. You will: - Keep Power steering - Keep A/C - Not have a gaping hole in your hood
Building an M90 Comptech from scratch like this will kill three birds with one stone. You will: - Keep Power steering - Keep A/C - Not have a gaping hole in your hood
0 2021/06/26 22:24:25
Going to install this cooler on the Comptech MP62 build. Made by MercRacing. ZZPerformances’ design is better, but they only make them for the Eaton M90.
Going to install this cooler on the Comptech MP62 build. Made by MercRacing. ZZPerformances’ design is better, but they only make them for the Eaton M90.
0 2021/06/29 06:19:02
Comptech MP62 cooler just came in from MercRacing! ZZP makes a better design, but they only make it for the Eaton M90. This cooler has no seal around the radiator and aluminum plate, so some of the charge will leak past the 1/4” gap, meaning less cooling affect. Perhaps I can use some sort of sealant to close the gap?
Comptech MP62 cooler just came in from MercRacing! ZZP makes a better design, but they only make it for the Eaton M90. This cooler has no seal around the radiator and aluminum plate, so some of the charge will leak past the 1/4” gap, meaning less cooling affect. Perhaps I can use some sort of sealant to close the gap?
0 2021/06/29 06:22:09