Motor mount - which one to replace?
#1
Instructor
Thread Starter
Motor mount - which one to replace?
Hi All,
2006 ML, Navi, 5sp AT, I began to feel/hear some clunking noise from underneath, possibly from front? Sounded like one or more of motor mounts have failed or is failing.
My questions are
1) how to find which one has failed or failing
2) is OEM the best replacement, if not which brand mounts you guys would recommend?
TL has only 94k miles on it, it's pretty strange to have motor mounts fail at this early stage. I still have original motor mounts on my other car(1999 ML320) at @217k miles. If the OEM mount last only this many miles, I don't feel like going with OEM, unless it's still the best available. Please share your expertise and experiences.
Thanks for all of your advices.
Steve
2006 ML, Navi, 5sp AT, I began to feel/hear some clunking noise from underneath, possibly from front? Sounded like one or more of motor mounts have failed or is failing.
My questions are
1) how to find which one has failed or failing
2) is OEM the best replacement, if not which brand mounts you guys would recommend?
TL has only 94k miles on it, it's pretty strange to have motor mounts fail at this early stage. I still have original motor mounts on my other car(1999 ML320) at @217k miles. If the OEM mount last only this many miles, I don't feel like going with OEM, unless it's still the best available. Please share your expertise and experiences.
Thanks for all of your advices.
Steve
#2
Instructor
Thread Starter
Acording to Rock Auto, DEA/MRC A4526HY (More Information for DEA/MRC A4526HY) to be OEM for FRONT mount, but doesn't show OEM right for right, recommendation please!!
#4
Instructor
Thread Starter
#5
OEM price doesn't sound too bad if you consider having to replace the front or rear again because aftermarket probably doesn't last as long. You'll have to remove the rubber shield on the mount to check but you might as well remove the whole mount at that point.
#6
Instructor
Thread Starter
Thanks for the kind advice.
I read a few articles on this subject at the Azine forum, rear mount tend to last very long time, like 200k+ miles.
I'm hoping rear mount is OK, going to do front & side mounts now and see that fixes the clunking sound.
I read a few articles on this subject at the Azine forum, rear mount tend to last very long time, like 200k+ miles.
I'm hoping rear mount is OK, going to do front & side mounts now and see that fixes the clunking sound.
#7
Senior Moderator
Visually inspect them
Trending Topics
#9
Instructor
To find out which mount failed, open the hood, put the car in 'Drive,' and slowly press the accelerator while holding the brake.
You can see the engine through the windshield in the gap between the hood and the wiper cowl.
If the engine lifts up significantly then the front mount is the one that failed.
Do it in 'Reverse gear' to see if the mount closest to the firewall is the failure point.
You can see the engine through the windshield in the gap between the hood and the wiper cowl.
If the engine lifts up significantly then the front mount is the one that failed.
Do it in 'Reverse gear' to see if the mount closest to the firewall is the failure point.
Last edited by JMiles_T; 10-06-2017 at 07:46 PM.
#10
Instructor
Thread Starter
To find out which mount failed, open the hood, put the car in 'Drive,' and slowly press the accelerator while holding the brake.
You can see the engine through the windshield in the gap between the hood and the wiper cowl.
If the engine lifts up significantly then the front mount is the one that failed.
Do it in 'Reverse gear' to see if the mount closest to the firewall is the failure point.
You can see the engine through the windshield in the gap between the hood and the wiper cowl.
If the engine lifts up significantly then the front mount is the one that failed.
Do it in 'Reverse gear' to see if the mount closest to the firewall is the failure point.
That makes a lot of sense, much appreciated.
I read in many posts, the rear mount last very long, like 200K+ miles, how's that sound?
#11
look for leaking fluid from front and rear mounts.
#12
Instructor
Thread Starter
#13
Instructor
Thread Starter
FRONT is definitely GONE,
To find out which mount failed, open the hood, put the car in 'Drive,' and slowly press the accelerator while holding the brake.
You can see the engine through the windshield in the gap between the hood and the wiper cowl.
If the engine lifts up significantly then the front mount is the one that failed.
Do it in 'Reverse gear' to see if the mount closest to the firewall is the failure point.
You can see the engine through the windshield in the gap between the hood and the wiper cowl.
If the engine lifts up significantly then the front mount is the one that failed.
Do it in 'Reverse gear' to see if the mount closest to the firewall is the failure point.
Steve
#14
Head a da Family
Join Date: Jul 2003
Location: New Friggin Jerzy
Age: 70
Posts: 5,505
Received 561 Likes
on
393 Posts
The side mount usually goes first, at least mine did followed by the front. Got the side replacement from rockauto, works fine!
There are good deals to be had on ebaY too, where I got my front and rear mounts.
.
.
There are good deals to be had on ebaY too, where I got my front and rear mounts.
.
.
#15
Race Director
Did they Ebay mounts have the vacuum line fittings? I'm guessing not... Link?
#16
Instructor
Thread Starter
What brand of side mount did you get from Rock Auto?
#18
Senior Moderator
https://www.google.com/search?q=diy+...hrome&ie=UTF-8
Use google, add "site:acurazine.com" and whatever your search criteria is. That's the best way to search this site.
Use google, add "site:acurazine.com" and whatever your search criteria is. That's the best way to search this site.
#19
Instructor
Thread Starter
https://www.google.com/search?q=diy+...hrome&ie=UTF-8
Use google, add "site:acurazine.com" and whatever your search criteria is. That's the best way to search this site.
Use google, add "site:acurazine.com" and whatever your search criteria is. That's the best way to search this site.
#20
YouTube is your friend. Just do a search for Acura TL engine mount and you'll find several videos for replacing them. If you're getting an "extra clunk" when you go over speed bumps or the like, it's probably your side mount. I ordered the genuine Acura part from Amazon:
I haven't done the front, but it's definitely more difficult than the side. The rear one is supposed to be the most difficult to replace. Good luck!
I haven't done the front, but it's definitely more difficult than the side. The rear one is supposed to be the most difficult to replace. Good luck!
#22
I went with OEM because my first one lasted 125K miles and for the extra $40-50 I'm hoping to get another 125K out of this one. Wasn't difficult to replace, but would rather not do it again if I don't have to...
#23
Instructor
Thread Starter
YouTube is your friend. Just do a search for Acura TL engine mount and you'll find several videos for replacing them. If you're getting an "extra clunk" when you go over speed bumps or the like, it's probably your side mount. I ordered the genuine Acura part from Amazon:
https://www.amazon.com/gp/product/B00FZN2TV0
I haven't done the front, but it's definitely more difficult than the side. The rear one is supposed to be the most difficult to replace. Good luck!
https://www.amazon.com/gp/product/B00FZN2TV0
I haven't done the front, but it's definitely more difficult than the side. The rear one is supposed to be the most difficult to replace. Good luck!
In both videos, neither had removed battery, just lifted engine a little to relieve pressure on engine mounts, and neither one on the jack stands. But the one DIY shown above on Azine had lifted on jackstands or ramps, removing the battery and heat shield as well. By removing more stuff out of the way, you'll get more room to work, but does it need to be lifted on jackstands?
#24
Senior Moderator
Why wouldn't you do things to make your life easier
#25
Instructor
Thread Starter
Are you saying that lifting on jackstands will make it easier?
Lifting on jackstands isn't a problem, but I'm asking if it makes replacing mounts easier.
Removing fans, radiator hose and battery tray are not that hard but a lot of work if not really necessary.
Lifting on jackstands isn't a problem, but I'm asking if it makes replacing mounts easier.
Removing fans, radiator hose and battery tray are not that hard but a lot of work if not really necessary.
#27
Yes, I've searched on YouTube videos, found a couple of them replacing side & front mounts on 3G TLs.
In both videos, neither had removed battery, just lifted engine a little to relieve pressure on engine mounts, and neither one on the jack stands. But the one DIY shown above on Azine had lifted on jackstands or ramps, removing the battery and heat shield as well. By removing more stuff out of the way, you'll get more room to work, but does it need to be lifted on jackstands?
In both videos, neither had removed battery, just lifted engine a little to relieve pressure on engine mounts, and neither one on the jack stands. But the one DIY shown above on Azine had lifted on jackstands or ramps, removing the battery and heat shield as well. By removing more stuff out of the way, you'll get more room to work, but does it need to be lifted on jackstands?
#28
Senior Moderator
I thought we were talking about the front/rear engine mounts.
#30
Senior Moderator
Yeah, so by doing the front, I can't see how you can do it without jacking up the car.
#31
Instructor
Thread Starter
In this and another YouTube videos, they're not lifting the car on jackstands, only lifting the engine a bit to relieve pressure off at mounts. This is my question.
The following users liked this post:
4drturbo (08-01-2024)
#32
Race Director
The only reason for using jack stands would be to make it easier if you needed to get under the car to attach the vacuum line. Otherwise, jack stands serve no purpose for this install. If you used jack stands, you still would need to jack the engine.
#33
Instructor
Thread Starter
If it is almost impossible to do it from above, I would begin by lifting it on jackstands. It will be much more time consuming to lift the car on jackstands while installing the mounts.
#34
Race Director
Sorry, I have yet to attempt this install, so I can't answer that question from experience. I think it entirely depends on how small your forearms are.
#36
Instructor
Thread Starter
More Than what I thought . . . not just motor mount
Well . . . replaced both side and front mounts, took me about 2.5 hrs, did lifted TL on jackstands but only removed coolant reservoir and screw holding O2 sensor and other wires. Side mount was indeed ripped abut 1/3, but front was still intact, replaced it anyway and keeping the old front mount (for now).
After replacing front and side mounts, took it for short drive, didn't expect much of improvement, and I was right. Something else is making noise at low speed around parking lot or I don't hear the noise during highway driving. Immediately I suspected the front right ball joint, took the FL tire off, checked the area, guess what I found! Front left BJ was replaced about a month ago, after another guy ripped off rubber boot with pickle fork(long story). I honestly thought this shop was honest and did a great job at reasonable cost, I brought my own part, the shop charged $177 for replacing the BJ and 4 wheel alignment.
I try not to think the shop screwed me up, but it doesn't look right with rubber boot was taped a few times with black electrical tape, please tell me what you think. Would this damaged ball joint make the kind of noise like broken motor mount? Pictures of ball joint area attached.
After replacing front and side mounts, took it for short drive, didn't expect much of improvement, and I was right. Something else is making noise at low speed around parking lot or I don't hear the noise during highway driving. Immediately I suspected the front right ball joint, took the FL tire off, checked the area, guess what I found! Front left BJ was replaced about a month ago, after another guy ripped off rubber boot with pickle fork(long story). I honestly thought this shop was honest and did a great job at reasonable cost, I brought my own part, the shop charged $177 for replacing the BJ and 4 wheel alignment.
I try not to think the shop screwed me up, but it doesn't look right with rubber boot was taped a few times with black electrical tape, please tell me what you think. Would this damaged ball joint make the kind of noise like broken motor mount? Pictures of ball joint area attached.
#37
Race Director
Wow, that's pathetic. Hard to tell, is the boot itself torn?
#38
Instructor
Thread Starter
I don't know. I haven't unwrapped the black tapes. Originally, the boot was good but was damaged by an idiot mechanic who used pickle fork trying to remove the BJ, the reason I had it replaced by shop.
I supplied the repair shop with brand new BJ from NAPA, boot shouldn't be cut, but looks like it was cut and leaking over the tape. What I think is, somehow the mechanic who did this job damaged the boot and trying to hide the mistake by wrapping up with tons of rlectrical tape. Sick!
I supplied the repair shop with brand new BJ from NAPA, boot shouldn't be cut, but looks like it was cut and leaking over the tape. What I think is, somehow the mechanic who did this job damaged the boot and trying to hide the mistake by wrapping up with tons of rlectrical tape. Sick!