2011 TL AWD model AC issue
#1
2011 TL AWD model AC issue
I have issue with my AC system. the blower motor keep runing crazy ( high speed) with hot air blow from front winshield. Can't control on AC console, press On/oFF, speed fan nothing. hit A/C button is engage. Anyone can't help me on this issue. Thanks.
#3
There is a self-diagnostic function for the HVAC. To run the self-diagnostic function, do the following:
1. Turn the ignition switch to LOCK (0) and then back to ON (II), or press the engine start/stop button to select the OFF mode and then the ON mode
2. Press and hold the FAN ON/OFF button, then within 10 seconds press and release the REAR WINDOW DEFOGGER/MIRROR DEFOGGER button five times Release the FAN ON/OFF button, then the self diagnostic begins.
If there is a problem with the system, it will flash AUTO, 88 and AUTO, 88 and WINDSHIELD DEFROST, or 88 and MODE. If there is more than one problems, they are displayed one at a time in sequence followed by a pause. If there are no problems detected, the segments do not illuminate, and the system appears to be turned off. The problems are displayed with some codes you may need to take it to the dealer to repair. There are lots of codes!!! If you have codes and you can post them I may be able to interpret them for you.
To cancel the self-diagnostic turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Hope that helps.
1. Turn the ignition switch to LOCK (0) and then back to ON (II), or press the engine start/stop button to select the OFF mode and then the ON mode
2. Press and hold the FAN ON/OFF button, then within 10 seconds press and release the REAR WINDOW DEFOGGER/MIRROR DEFOGGER button five times Release the FAN ON/OFF button, then the self diagnostic begins.
If there is a problem with the system, it will flash AUTO, 88 and AUTO, 88 and WINDSHIELD DEFROST, or 88 and MODE. If there is more than one problems, they are displayed one at a time in sequence followed by a pause. If there are no problems detected, the segments do not illuminate, and the system appears to be turned off. The problems are displayed with some codes you may need to take it to the dealer to repair. There are lots of codes!!! If you have codes and you can post them I may be able to interpret them for you.
To cancel the self-diagnostic turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Hope that helps.
The following users liked this post:
echodigital (08-28-2014)
#6
The shop repair manual was posted here, a while back: https://acurazine.com/forums/4g-tl-2009-2014-123/acura-tl-service-manual-899572/
Its on page 21-100.
#7
There is a self-diagnostic function for the HVAC. To run the self-diagnostic function, do the following:
1. Turn the ignition switch to LOCK (0) and then back to ON (II), or press the engine start/stop button to select the OFF mode and then the ON mode
2. Press and hold the FAN ON/OFF button, then within 10 seconds press and release the REAR WINDOW DEFOGGER/MIRROR DEFOGGER button five times Release the FAN ON/OFF button, then the self diagnostic begins.
If there is a problem with the system, it will flash AUTO, 88 and AUTO, 88 and WINDSHIELD DEFROST, or 88 and MODE. If there is more than one problems, they are displayed one at a time in sequence followed by a pause. If there are no problems detected, the segments do not illuminate, and the system appears to be turned off. The problems are displayed with some codes you may need to take it to the dealer to repair. There are lots of codes!!! If you have codes and you can post them I may be able to interpret them for you.
To cancel the self-diagnostic turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Hope that helps.
1. Turn the ignition switch to LOCK (0) and then back to ON (II), or press the engine start/stop button to select the OFF mode and then the ON mode
2. Press and hold the FAN ON/OFF button, then within 10 seconds press and release the REAR WINDOW DEFOGGER/MIRROR DEFOGGER button five times Release the FAN ON/OFF button, then the self diagnostic begins.
If there is a problem with the system, it will flash AUTO, 88 and AUTO, 88 and WINDSHIELD DEFROST, or 88 and MODE. If there is more than one problems, they are displayed one at a time in sequence followed by a pause. If there are no problems detected, the segments do not illuminate, and the system appears to be turned off. The problems are displayed with some codes you may need to take it to the dealer to repair. There are lots of codes!!! If you have codes and you can post them I may be able to interpret them for you.
To cancel the self-diagnostic turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Hope that helps.
When I ran the test, it displayed Auto then 88, Auto then defroster and it repeated that cycle again and again. Does that mean there is a problem(s) ?
Trending Topics
#8
Instructor
There is a self-diagnostic function for the HVAC. To run the self-diagnostic function, do the following:
1. Turn the ignition switch to LOCK (0) and then back to ON (II), or press the engine start/stop button to select the OFF mode and then the ON mode
2. Press and hold the FAN ON/OFF button, then within 10 seconds press and release the REAR WINDOW DEFOGGER/MIRROR DEFOGGER button five times Release the FAN ON/OFF button, then the self diagnostic begins.
If there is a problem with the system, it will flash AUTO, 88 and AUTO, 88 and WINDSHIELD DEFROST, or 88 and MODE. If there is more than one problems, they are displayed one at a time in sequence followed by a pause. If there are no problems detected, the segments do not illuminate, and the system appears to be turned off. The problems are displayed with some codes you may need to take it to the dealer to repair. There are lots of codes!!! If you have codes and you can post them I may be able to interpret them for you.
To cancel the self-diagnostic turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Hope that helps.
1. Turn the ignition switch to LOCK (0) and then back to ON (II), or press the engine start/stop button to select the OFF mode and then the ON mode
2. Press and hold the FAN ON/OFF button, then within 10 seconds press and release the REAR WINDOW DEFOGGER/MIRROR DEFOGGER button five times Release the FAN ON/OFF button, then the self diagnostic begins.
If there is a problem with the system, it will flash AUTO, 88 and AUTO, 88 and WINDSHIELD DEFROST, or 88 and MODE. If there is more than one problems, they are displayed one at a time in sequence followed by a pause. If there are no problems detected, the segments do not illuminate, and the system appears to be turned off. The problems are displayed with some codes you may need to take it to the dealer to repair. There are lots of codes!!! If you have codes and you can post them I may be able to interpret them for you.
To cancel the self-diagnostic turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Hope that helps.
Thread
Thread Starter
Forum
Replies
Last Post
Legend2TL
Motorsports News
13
01-31-2016 09:27 AM