AcuraZine - Acura Enthusiast Community
0 2024/11/03 08:37:14
0 2024/11/03 08:27:29
0 2024/08/28 11:31:14
0 2024/08/19 16:47:11
0 2024/07/07 08:16:35
0 2024/06/11 11:49:03
0 2024/06/11 11:48:13
Head gasket failure top piston
Head gasket failure top piston
0 2024/06/04 12:54:57
Top piston had head gasket failure
Top piston had head gasket failure
0 2024/06/04 12:49:44
Left cylinder had head gasket failure
Left cylinder had head gasket failure
0 2024/06/04 12:49:42
0 2024/05/15 08:35:39
0 2024/04/19 09:35:56
0 2024/04/19 09:26:17
Lube here
Lube here
0 2024/03/28 13:25:40
Lube here
Lube here
0 2024/03/28 13:21:24
0 2024/01/23 11:06:52
0 2024/01/23 11:06:19
0 2024/01/23 09:08:37
0 2023/12/04 14:53:02
0 2023/12/01 07:58:55
0 2023/11/20 08:49:33
0 2023/11/09 10:59:57
0 2023/11/09 10:53:04
Worn eyebolt and pin, you can replace just the eyebolt if the pin is not badly worn but the pin is typically worn too.
Worn eyebolt and pin, you can replace just the eyebolt if the pin is not badly worn but the pin is typically worn too.
0 2023/11/01 10:14:13
In the rear of the engine and viewing from the left side look carefully at the eyebolt and pin for any gap between the eyebolt hole and the pin.
In the rear of the engine and viewing from the left side look carefully at the eyebolt and pin for any gap between the eyebolt hole and the pin.
0 2023/11/01 10:10:36
Small pit where tri-pod bearing slides back and forth causes vibration during acceleration.
Small pit where tri-pod bearing slides back and forth causes vibration during acceleration.
0 2023/08/09 08:26:20
0 2023/07/03 20:24:42
0 2023/07/01 16:38:07
0 2023/06/27 19:06:50
A little tricky but guided the new parts into the linkage arm hole.
A little tricky but guided the new parts into the linkage arm hole.
0 2023/06/27 19:06:35
Finally got the rivetted pin shaft out of the linkage arm, this was the most challenging part of the repair. Still trying to think of a good method to get the shaft part of the pin out of the linkage arm.
Finally got the rivetted pin shaft out of the linkage arm, this was the most challenging part of the repair. Still trying to think of a good method to get the shaft part of the pin out of the linkage arm.
0 2023/06/27 19:06:24
Used a hand-held belt type sander to grind off rivet head. This type of tool ground off the rivet head in a short amount of time.
Used a hand-held belt type sander to grind off rivet head. This type of tool ground off the rivet head in a short amount of time.
0 2023/06/27 19:05:57
New parts assembled and ready for install, threads of shoulder bolt were shorten some
New parts assembled and ready for install, threads of shoulder bolt were shorten some
0 2023/06/27 19:05:39
Over the counter parts, shoulder pin modified, two stainless steel ball bearings used, not shown a spacer and thrust washer.
Over the counter parts, shoulder pin modified, two stainless steel ball bearings used, not shown a spacer and thrust washer.
0 2023/06/27 19:05:25
Large gap visible, play in linkage pivot point causing P2263 code.
Large gap visible, play in linkage pivot point causing P2263 code.
0 2023/06/27 19:05:06
Both eyebolt and pin worn by ~2mm
Both eyebolt and pin worn by ~2mm
0 2023/06/27 19:04:50
Youtube video screen capture of a worn variable vane actuator linkage pin. This is the pin the eye-bolt pivots on and this is the eye-bolt known for wear and the P2263 code. Eye bolt available, this linkage arm pin is not.
Youtube video screen capture of a worn variable vane actuator linkage pin. This is the pin the eye-bolt pivots on and this is the eye-bolt known for wear and the P2263 code. Eye bolt available, this linkage arm pin is not.
0 2023/06/17 19:45:17
0 2015/11/29 11:33:44
Pitted area within inner CV joint causing vibration.
Pitted area within inner CV joint causing vibration.
0 2015/11/28 22:27:03