AcuraZine - Acura Enthusiast Community
Pulled these straight from my garden. Six sprinkler heads are dedicated just for the garden area so they grow maintainence free.
Pulled these straight from my garden. Six sprinkler heads are dedicated just for the garden area so they grow maintainence free.
0 2021/06/09 19:27:13
0 2021/06/08 10:37:18
0 2021/06/08 10:37:08
0 2021/06/08 10:36:55
Picked up that good-good(And none of that bad-bad).
Picked up that good-good(And none of that bad-bad).
0 2021/06/07 23:01:17
Heeltoe TSX, Woop-Woop!
Heeltoe TSX, Woop-Woop!
0 2021/06/07 23:01:03
0 2021/06/07 22:02:02
0 2021/06/07 22:01:54
0 2021/06/07 22:01:45
Use only original fellers!
Use only original fellers!
0 2021/06/07 22:01:35
0 2021/06/07 21:59:15
0 2021/06/07 21:59:06
0 2021/06/07 21:58:58
0 2021/06/07 21:58:48
0 2021/06/06 22:12:41
Tomatoes are coming in nice đź‘Ť
Tomatoes are coming in nice đź‘Ť
0 2021/06/06 22:08:06
0 2021/06/06 22:06:59
Began cleaning the engine bay as the only seals that may still leak is the oil pump housing. I’m going to mate the trans and engine back together tomorrow, then begin reassembly.
Began cleaning the engine bay as the only seals that may still leak is the oil pump housing. I’m going to mate the trans and engine back together tomorrow, then begin reassembly.
0 2021/06/05 22:43:46
Took a bit to get the rear mount hydronic tube back on. If you go under the car and remove the 12mm bolt securing the tube, you will get enough slack to easily resecure it.
Took a bit to get the rear mount hydronic tube back on. If you go under the car and remove the 12mm bolt securing the tube, you will get enough slack to easily resecure it.
0 2021/06/05 22:43:37
Changed rear mount
Changed rear mount
0 2021/06/05 22:43:31
Changed rear cam seal
Changed rear cam seal
0 2021/06/05 22:43:26
0 2021/06/05 11:08:11
0 2021/06/05 11:08:03
0 2021/06/05 11:07:56
I have here an MP90 from 1991 Mustang/Camaro. It’s says 3.8 on the bottom on the underbelly. It’s very compact but the bolt pattern is the similar to the Eaton M90 Gen 3. A custom plate would have to be made
I have here an MP90 from 1991 Mustang/Camaro. It’s says 3.8 on the bottom on the underbelly. It’s very compact but the bolt pattern is the similar to the Eaton M90 Gen 3. A custom plate would have to be made
0 2021/06/05 11:07:50
0 2021/06/05 11:07:44
0 2021/06/03 22:51:36
0 2021/06/03 22:44:43
0 2021/06/03 22:44:36
0 2021/06/03 22:44:28
I’d say it was time to change the clutch disk.
I’d say it was time to change the clutch disk.
0 2021/06/03 09:18:18
Haven’t seen a clutch so worn out before. ...Though I’ve only replaced a couple. But those clutch disks were spinning and had more met on them, but the cars were not stock.
Haven’t seen a clutch so worn out before. ...Though I’ve only replaced a couple. But those clutch disks were spinning and had more met on them, but the cars were not stock.
0 2021/06/03 07:43:07
0 2021/06/03 07:26:59
Alright fellas, no more messing around. It’s time to do the real part of the surgery.
Alright fellas, no more messing around. It’s time to do the real part of the surgery.
0 2021/06/03 07:26:51
0 2021/06/03 00:14:58
0 2021/06/03 00:14:53
0 2021/06/03 00:14:47
0 2021/06/03 00:14:38
0 2021/06/03 00:14:31
0 2021/06/03 00:14:23