AcuraZine - Acura Enthusiast Community
0 2015/07/31 08:58:29
Before with stock Eagle Ls2
Before with stock Eagle Ls2
0 2015/09/22 09:46:08
0 2015/09/22 09:46:12
0 2015/09/22 09:46:15
0 2015/09/22 09:48:07
0 2015/09/22 09:48:11
0 2015/09/22 09:48:14
I had to unscrew two screws near the bottom right and bend that plastic peace back in order to get my hand up there and unplug it.
I had to unscrew two screws near the bottom right and bend that plastic peace back in order to get my hand up there and unplug it.
0 2016/08/09 10:13:23
There it is installed now
There it is installed now
0 2016/08/09 10:14:44
I put in the user interface cord under the carpet and brought it up to center console
I put in the user interface cord under the carpet and brought it up to center console
0 2016/08/09 10:15:22
Last I strung the wire into the bottom then back up the other side. If you notice there are two notches for wires then I can close the top slide and it is out of the way unless I need to change the setting
Last I strung the wire into the bottom then back up the other side. If you notice there are two notches for wires then I can close the top slide and it is out of the way unless I need to change the setting
0 2016/08/09 10:16:25
2014 3.7 TL-SHAWD. High Flow cat and reflash
2014 3.7 TL-SHAWD. High Flow cat and reflash
0 2017/03/05 16:57:19
245/35/20. H&R sport spring yes on AWD it works. 1 finger gap front. 1.5 ginger gap back
245/35/20. H&R sport spring yes on AWD it works. 1 finger gap front. 1.5 ginger gap back
0 2018/03/27 18:56:07
0 2018/03/30 10:38:00
0 2018/03/30 10:38:32
Notice the camber on the rear stock rim.
Notice the camber on the rear stock rim.
0 2018/03/30 10:40:13
0 2018/03/30 10:48:22
0 2018/03/30 10:51:23
0 2018/03/30 10:53:25
Notice the better camber and with the wider wheel it is more flush but not quite complete
Notice the better camber and with the wider wheel it is more flush but not quite complete
0 2018/03/30 10:53:48
Hubcentric 5x114.3 (64.1 bore) 3mm aircraft aluminum spacers for the front by Euro Motor Werkes. Anything more than 3mm would require longer studs.
Hubcentric 5x114.3 (64.1 bore) 3mm aircraft aluminum spacers for the front by Euro Motor Werkes. Anything more than 3mm would require longer studs.
0 2018/03/30 11:06:56
Eight prince (made in Japan) 15mm 12/1.50 5x114.3 6061 aluminum with heat treated carbon steel studs. For the rear wheels
Eight prince (made in Japan) 15mm 12/1.50 5x114.3 6061 aluminum with heat treated carbon steel studs. For the rear wheels
0 2018/03/30 11:10:06
hubcenteric rings 64.1mm bore
hubcenteric rings 64.1mm bore
0 2018/03/30 11:11:39
put together for a tight fit
put together for a tight fit
0 2018/03/30 11:12:26
0 2018/03/30 11:19:07
rear of rim. Notice the gaps for the wheel stud to go into that extends past the spacer
rear of rim. Notice the gaps for the wheel stud to go into that extends past the spacer
0 2018/03/30 11:19:25
Front rotor without spacer and as a side note the studs measure 27mm in the current photo.
Front rotor without spacer and as a side note the studs measure 27mm in the current photo.
0 2018/03/30 11:20:58
3mm hubcentric spacer installed. Firm fit around hub
3mm hubcentric spacer installed. Firm fit around hub
0 2018/03/30 11:21:23
From side. Applied anti seize to reverse side
From side. Applied anti seize to reverse side
0 2018/03/30 11:22:05
0 2018/03/30 11:23:28
front installed 3mm spacer
front installed 3mm spacer
0 2018/03/30 11:23:53
Eight Prince spacer installed after cleaning hub and applying anti seize to reverse side. As you can see I have blue lock tight on the stock lug threads
Eight Prince spacer installed after cleaning hub and applying anti seize to reverse side. As you can see I have blue lock tight on the stock lug threads
0 2018/03/30 11:25:04
torques to 85lbs
torques to 85lbs
0 2018/03/30 11:26:16
After install and torques 30.5mm eight prince threads to 85lbs. notice the space provided for the stuck thread to be so it doesn't hit the rim
After install and torques 30.5mm eight prince threads to 85lbs. notice the space provided for the stuck thread to be so it doesn't hit the rim
0 2018/03/30 11:26:49
Final look
Final look
0 2018/03/30 11:28:36
0 2018/03/30 11:29:03
Finished product. 1 tight index finger between front tire and fender and 1 loose fit index finger between rear wheel and fender
Finished product. 1 tight index finger between front tire and fender and 1 loose fit index finger between rear wheel and fender
0 2018/03/30 11:31:44
0 2018/03/30 11:32:43
0 2018/03/30 11:32:55
75.99mm at the manifold.
75.99mm at the manifold.
0 2018/04/10 21:04:32