Delta's 2018 Still Night A-Spec TLX build
yeah, but I just don't see the point. This car is anything but a performance car. Market it however they want, it just doesn't have the power which would justify the money on a BBK. I'll just have to wait for brembos when I get a hellcat or a GTR or something else next
Safety Car
Joined: Dec 2014
Posts: 4,663
Likes: 834
Then again it if I had a 11 inch personality like you, I would get hot women like you and wouldn’t have to dabble In 909 SSBBW always
Racer
Joined: Oct 2017
Posts: 358
Likes: 171
I, too, have the Still Night Blue Pearl TLX, and I followed your mods with interest. More specifically, the SFactor Fabrication Splitter kit. I email SFactor Fab to inquire about installation requirements, but never received an email back from them. Is there any drilling or front bumper removal required. Is there any way you can pdf your installation instructions and email them to me? Thanks, Rob
I, too, have the Still Night Blue Pearl TLX, and I followed your mods with interest. More specifically, the SFactor Fabrication Splitter kit. I email SFactor Fab to inquire about installation requirements, but never received an email back from them. Is there any drilling or front bumper removal required. Is there any way you can pdf your installation instructions and email them to me? Thanks, Rob
Racer
Joined: Oct 2017
Posts: 358
Likes: 171
Thank you for your response. I looked at the rear bumper on my car and I'm sure that will require drilling because there aren't any existing holes. What about the rocker moldings, any drilling to install the side pieces?
sorry, yeah. Those will require 3M double sided tape and self tapping screws that come with the kit. The sides are pre drilled. Basically 3 small holes in the inner lip of the rear bumper and a handful of small holes down the under side of the side skirts. Nothing you would ever see if you removed the kit later.
Thanks again for all the compliments guys. Here's a little before and after. The white TLX in the top pic is what I traded for this one.
Last edited by deltaboxxx; Oct 26, 2017 at 12:39 PM.
Joined: Sep 2008
Posts: 78,245
Likes: 20,199
it's there...
wow, i see why you needed that front diffuser...they flattened the front of the aspec considerably, right? Or is that the angle of the dangle?
wow, i see why you needed that front diffuser...they flattened the front of the aspec considerably, right? Or is that the angle of the dangle?
6 Forward 1 Back
Joined: Feb 2001
Posts: 2,400
Likes: 312
From: Bay Area CA
Racer
Joined: Oct 2017
Posts: 358
Likes: 171
What do you think about the sideskirt extension attached to the rear bumper? From some angles, it doesn't appear to integrate with the rear bumper, like the rear part of the skirt should be more tapered so it doesn't stick out as much. Is it just the angle in the picture?
So, when you removed the front license plate holder, it didn't leave holes?
What do you think about the sideskirt extension attached to the rear bumper? From some angles, it doesn't appear to integrate with the rear bumper, like the rear part of the skirt should be more tapered so it doesn't stick out as much. Is it just the angle in the picture?
What do you think about the sideskirt extension attached to the rear bumper? From some angles, it doesn't appear to integrate with the rear bumper, like the rear part of the skirt should be more tapered so it doesn't stick out as much. Is it just the angle in the picture?
edit: the holes are there but not very noticeable. It just looks like a bug if anything. The color is dark enough not to notice. I specifically told them not to install the plates before the car was delivered, however it was a dealer trade and the other dealer already had installed it
Last edited by deltaboxxx; Oct 26, 2017 at 08:30 PM.