19x9.5/19x11 Fitment Question!
#1
19x9.5/19x11 Fitment Question!
Anyone running or know someone running aggressive specs? I'm looking into a new set of wheels for next year and was curious if any of y'all know if it'd work heh.
Complete specs are from a 2P wheel. Fronts are 19x9.5 +20 and rears are 19x11 +25. When checking out the fitment guide on WillTheyFit, it's poking about 1.5cm more in the fronts and 1.7cm in the rear than my current setup, which isn't too crazy I guess? (Fronts: 19x8.5 +15 Rears: 19x9.5 +20).
Complete specs are from a 2P wheel. Fronts are 19x9.5 +20 and rears are 19x11 +25. When checking out the fitment guide on WillTheyFit, it's poking about 1.5cm more in the fronts and 1.7cm in the rear than my current setup, which isn't too crazy I guess? (Fronts: 19x8.5 +15 Rears: 19x9.5 +20).
#3
#5
Of course u can fit them
I'm running 10.5 all 4 +35 front +25 rear and I just roll the fenders and pull them a little no camber kit but if u gone go low like I did u gone get 2-3 degrees camber
Your set up gone be 3mm more on front and 6mm on rear then my with is not a lot of course u gone need to work a little to fit them like cut the front liners cause after u roll and pull the fender they not gone be attached to it
And I run 245/35/20
I would like to see the wheels u want to get
Good lucky
I'm running 10.5 all 4 +35 front +25 rear and I just roll the fenders and pull them a little no camber kit but if u gone go low like I did u gone get 2-3 degrees camber
Your set up gone be 3mm more on front and 6mm on rear then my with is not a lot of course u gone need to work a little to fit them like cut the front liners cause after u roll and pull the fender they not gone be attached to it
And I run 245/35/20
I would like to see the wheels u want to get
Good lucky
The following users liked this post:
carbonTSEX (04-16-2016)
#6
Of course u can fit them
I'm running 10.5 all 4 +35 front +25 rear and I just roll the fenders and pull them a little no camber kit but if u gone go low like I did u gone get 2-3 degrees camber
Your set up gone be 3mm more on front and 6mm on rear then my with is not a lot of course u gone need to work a little to fit them like cut the front liners cause after u roll and pull the fender they not gone be attached to it
And I run 245/35/20
I would like to see the wheels u want to get
Good lucky
I'm running 10.5 all 4 +35 front +25 rear and I just roll the fenders and pull them a little no camber kit but if u gone go low like I did u gone get 2-3 degrees camber
Your set up gone be 3mm more on front and 6mm on rear then my with is not a lot of course u gone need to work a little to fit them like cut the front liners cause after u roll and pull the fender they not gone be attached to it
And I run 245/35/20
I would like to see the wheels u want to get
Good lucky
Trending Topics
#9
#10
35 series is life. And Carbon, you can't keep teasing me about those wheels man. It's starting to take an emotional toll on me .
And the wheels are Work Meister S13P. Either powder coated Metallic copper or Black Face/Copper barrel.
Closest example I can find.
And the wheels are Work Meister S13P. Either powder coated Metallic copper or Black Face/Copper barrel.
Closest example I can find.
#11
The Meisters go hard.
Thread
Thread Starter
Forum
Replies
Last Post
tepioka92
ILX Tires, Wheels & Suspension
11
04-27-2017 06:50 PM
johnpancakes014
2G TL Tires, Wheels & Suspension
0
03-21-2016 12:23 AM
Marmstrong1023
2G TSX Tires, Wheels & Suspension
2
01-25-2016 08:36 AM