Rockstar143's '04 RYP S2000 Progress Thread **Updated Regularly**
The following users liked this post:
rockstar143 (04-01-2015)
The following users liked this post:
rockstar143 (04-01-2015)
The following users liked this post:
rockstar143 (04-01-2015)
The following users liked this post:
rockstar143 (04-03-2015)
The following users liked this post:
TLDude876 (04-05-2015)
#2185
Thread Starter
Moderator
Chapter Leader (South Florida Region)
Chapter Leader (South Florida Region)
iTrader: (6)
Joined: Sep 2008
Posts: 78,016
Likes: 20,031
Back for round 2 with my 2nd S!
15/20MM...after driving around last night a bit and today...I didn't even have to roll fenders. I'd rather take the fender approach very slowly if need be, this time around.
With a push from my buddy Dennis...gave DMV motorsport spacers a shot...great quality...fixed center, 17MM nuts on the 15 and 19MM on the 20...
Had to sand and apply some bearing grease (I always do for ease of removal later). Also, a little trick I use to put the spacers on the front by myself using a breaker bar.
DSC_8098 by swimex37, on Flickr
DSC_8101 by swimex37, on Flickr
DSC_8102 by swimex37, on Flickr
Before:
DSC_8099 by swimex37, on Flickr
After:
DSC_8103 by swimex37, on Flickr
Absolutely perfect...not too aggressive, but pretty flush!
DSC_8116 by swimex37, on Flickr
DSC_8117 by swimex37, on Flickr
DSC_8120 by swimex37, on Flickr
DSC_8126 by swimex37, on Flickr
DSC_8128 by swimex37, on Flickr
I'm slightly less low than I was on the Sebring one...I can still get the jack under the sides without 2x4.
DSC_8129 by swimex37, on Flickr
The following 3 users liked this post by rockstar143:
The following users liked this post:
rockstar143 (04-07-2015)
The following 2 users liked this post by CLassy02:
rockstar143 (04-07-2015),
thoiboi (04-13-2015)
#2194
Thread Starter
Moderator
Chapter Leader (South Florida Region)
Chapter Leader (South Florida Region)
iTrader: (6)
Joined: Sep 2008
Posts: 78,016
Likes: 20,031
Funny thing about that Van...it's a van that's converted for a kid that lives there that is in a wheelchair. But it's been defunct since we moved in (and judging from the mold on it, probably years)...from what my other neighbor told me...it's where they stash their pot.
but I would totally buy it dirt cheap and get it going and pick up some blow pops and swing by the nearest schools at 11mph around 245pm though
Thanks Austin!
Funny...me too!
Initially, I did...then I compared to the Sebring one that was lowered on spacers and was like, FACKKK I want V2 wheels! Actually, my buddy Mike offered to swap with me when he sold his white one the day after I bought this one and I turned him down.
Now that they're spaced out and lowered too though...I agree! I really LOVE how they look very much!
but I would totally buy it dirt cheap and get it going and pick up some blow pops and swing by the nearest schools at 11mph around 245pm though
Funny...me too!
Initially, I did...then I compared to the Sebring one that was lowered on spacers and was like, FACKKK I want V2 wheels! Actually, my buddy Mike offered to swap with me when he sold his white one the day after I bought this one and I turned him down.
Now that they're spaced out and lowered too though...I agree! I really LOVE how they look very much!
#2195
Holy rusty rotors Batman!!
Haha, i'm sure your solution is already in motion but i couldn't resist. Spacers look great (i use those same sizes on my Aspecs). I think your conservative approach this time around is great, it maintains a bit more of the heritage of the car and that is a good thing.
#2196
Thread Starter
Moderator
Chapter Leader (South Florida Region)
Chapter Leader (South Florida Region)
iTrader: (6)
Joined: Sep 2008
Posts: 78,016
Likes: 20,031
LOL...
I'll address that eventually. I'll probably remove and paint them and the calipers . No need to spend extra scratch on new rotors since these still have tons of meat! I might go with a silver or gunmetal instead of the black I did last time.
I was conservative with the silver one though...you should see what some of these crazy kids are doing!
I'll address that eventually. I'll probably remove and paint them and the calipers . No need to spend extra scratch on new rotors since these still have tons of meat! I might go with a silver or gunmetal instead of the black I did last time.
I was conservative with the silver one though...you should see what some of these crazy kids are doing!
The following users liked this post:
The Machine (04-14-2015)
#2199
Nice, nice car....I'd love one, but will have to be content with the TL, RDX, Civic, and Accord. With 3 kids, two of them driving now, I can't afford any more car deals....sad, but that's life. Very pretty car. Thanks for sharing.
The following users liked this post:
rockstar143 (04-08-2015)