My last rotary project/project.... 3 rotor RX-7
#362
Instructor
Thread Starter
#363
Instructor
Thread Starter
So, Update continues..
I pulled the engine out of my FD.. old engined worked fine. Did over 10 trackdays in a year and several out of state trips.
While it was out did could of add ons.. Like this IRP Brake MC brace.
Also added new oil coolers..
And I decided to drop the subframe to install because I needed to also change out the coilovers.
I also added Radium Competition oil catch can and IR Performance Oil filler neck
Full Function Fuel Rails for 13B-RE LIM, Full Function Oil Filter neck, and few other new parts.. Anyhow long block is ready to install
Engine in!
Also upgraded fuel system using Radium Fuel Surge tank with Bosch 044 pump inside.
Stance Super Sport + coils installed!
Engine is port matched for 13B-RE Cosmo LIM and UIM.. I'm running sequential twin set up for this..
Installed some polished goodies
I pulled the engine out of my FD.. old engined worked fine. Did over 10 trackdays in a year and several out of state trips.
While it was out did could of add ons.. Like this IRP Brake MC brace.
Also added new oil coolers..
And I decided to drop the subframe to install because I needed to also change out the coilovers.
I also added Radium Competition oil catch can and IR Performance Oil filler neck
Full Function Fuel Rails for 13B-RE LIM, Full Function Oil Filter neck, and few other new parts.. Anyhow long block is ready to install
Engine in!
Also upgraded fuel system using Radium Fuel Surge tank with Bosch 044 pump inside.
Stance Super Sport + coils installed!
Engine is port matched for 13B-RE Cosmo LIM and UIM.. I'm running sequential twin set up for this..
Installed some polished goodies
#364
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
#368
Instructor
Thread Starter
More Update..
I started to add some rare parts I had..
C's short shifter.
Mounted the Radium Surge Tank
Chase Bay overflow tank and eliminated OE tank.
Finally its all bolted up
Andy from Adaptronics flew in from Australia and with Elliot from Turblown, they came down to Birmingham AL to tune my car.
Video of the dyno run..
Due to some boost controlling issue, we ended the tuning and decided to do couple of days later.
Couple of days later (day when all of us were heading to PRI) I brought these with me in case..
Here is Andy watching the car being loaded.
And done!
Several days later, while trying to put some miles on the engine and such, I ran into my friend Zach with 20B.
[/URL]
I started to add some rare parts I had..
C's short shifter.
Mounted the Radium Surge Tank
Chase Bay overflow tank and eliminated OE tank.
Finally its all bolted up
Andy from Adaptronics flew in from Australia and with Elliot from Turblown, they came down to Birmingham AL to tune my car.
Video of the dyno run..
Due to some boost controlling issue, we ended the tuning and decided to do couple of days later.
Couple of days later (day when all of us were heading to PRI) I brought these with me in case..
Here is Andy watching the car being loaded.
And done!
Several days later, while trying to put some miles on the engine and such, I ran into my friend Zach with 20B.
[/URL]
#371
Instructor
Thread Starter
#372
Instructor
Thread Starter
Quick recall from PRI in Indy..
Couple of cool stuff I saw at PRI
Davies Craig EWP
Holley's new fuel pump sock
Alpinestars gloves
And got to have steak at St. Elmos place.. little hyped but good.
Back to the project updates.
So... got these lights
And also changed the color on the car.
Trying out what wheels will go with the new color..
Decided on the Volk Racing RE30
Hit the local car meet
Track day at Barber Motorsports Park, with Just Track It! They are one of the best groups to track with.
Couple of cool stuff I saw at PRI
Davies Craig EWP
Holley's new fuel pump sock
Alpinestars gloves
And got to have steak at St. Elmos place.. little hyped but good.
Back to the project updates.
So... got these lights
And also changed the color on the car.
Trying out what wheels will go with the new color..
Decided on the Volk Racing RE30
Hit the local car meet
Track day at Barber Motorsports Park, with Just Track It! They are one of the best groups to track with.
#374
Instructor
Thread Starter
#375
Turd Polisher
iTrader: (1)
Your Instagram page is - following!
#377
Instructor
Thread Starter
More Update..
I had a photoshoot with Ryan Lopez, who shot my car other times.. I can't share those photos yet as they are still in bound to a media for publication.. but here are some I took..
Ryan Lopez's shoes matching the color of the car.
Preview of one of the shot
Couple of other things...
I put my SSM at my friend's house
Also started to work on my engine harness at Chase Bays. No one have made a quick disconnect for sequential twin
And since I'm a family man and with a dog, I been secretly searching online for a unicorn... Lexus IS300 Wagon. And finally found one!! 2005 Sportcross, only 1 of 240 ish sold in USA.
And had to get a custom plate
I had some old SSR's from my FD and put some new Toyo T1-Sports on them. I had great luck with these tires.
Talking about wheels.. I also picked up a set of MS-01S in 18s for the FD. Bought them throught GTR-Garage on Yahoo auction japan. Those of you looking for people to bring in large parts from japan, GTR Garage is the place! More info and their contact, GTR Garage
I had a photoshoot with Ryan Lopez, who shot my car other times.. I can't share those photos yet as they are still in bound to a media for publication.. but here are some I took..
Ryan Lopez's shoes matching the color of the car.
Preview of one of the shot
Couple of other things...
I put my SSM at my friend's house
Also started to work on my engine harness at Chase Bays. No one have made a quick disconnect for sequential twin
And since I'm a family man and with a dog, I been secretly searching online for a unicorn... Lexus IS300 Wagon. And finally found one!! 2005 Sportcross, only 1 of 240 ish sold in USA.
And had to get a custom plate
I had some old SSR's from my FD and put some new Toyo T1-Sports on them. I had great luck with these tires.
Talking about wheels.. I also picked up a set of MS-01S in 18s for the FD. Bought them throught GTR-Garage on Yahoo auction japan. Those of you looking for people to bring in large parts from japan, GTR Garage is the place! More info and their contact, GTR Garage
#378
Instructor
Thread Starter
Catching up on my updates..
So, I've decided to pull the dip off and rock my Montego Blue paint. But to protect the paint, I've added some dip to areas where its prone to chipping.. Mainly using Toyo Tires, R888's.
Also, I was getting my RZ Recaro Carbon Kevlar seats recovered.
I didn't want something too crazy, so sticking with neutral grey suede.
perforated center cushions
All the original material removed.. I'm saving it in case for the future..
Meanwhile, still working on the OE harness at Chase Bays.. Completely disassembled and ID'd.
Also, working on a bumper. I've been a huge fan of FEED (Fujita Engineering) and RE-Amemiya. Both bumper has its positives and wanted to build a bumper that utilizes best of the both.
I was one of the first in USA to have the FEED Type 2R bumper and lights and its the signal Driving lights of Type 2R that I loved.
What I liked about the RE-Amemiya was the lower half. The aggressiveness of the lower half of the RE-A bumper is what I loved. Hence My 20B FD has the RE-Amemiya N1-02 bumper. So, I fused the two together.
But what I did not like about either bumper is the center lower section raised. This caused a problem when wanting to use front splitter. So, we are making it flat.
Everything smooth out
And Mold being made.. (credit goes to LC Racing for making the mold).
Bumper is currently on my car and few things to be adjusted and new mold needs to be made.
So, I've decided to pull the dip off and rock my Montego Blue paint. But to protect the paint, I've added some dip to areas where its prone to chipping.. Mainly using Toyo Tires, R888's.
Also, I was getting my RZ Recaro Carbon Kevlar seats recovered.
I didn't want something too crazy, so sticking with neutral grey suede.
perforated center cushions
All the original material removed.. I'm saving it in case for the future..
Meanwhile, still working on the OE harness at Chase Bays.. Completely disassembled and ID'd.
Also, working on a bumper. I've been a huge fan of FEED (Fujita Engineering) and RE-Amemiya. Both bumper has its positives and wanted to build a bumper that utilizes best of the both.
I was one of the first in USA to have the FEED Type 2R bumper and lights and its the signal Driving lights of Type 2R that I loved.
What I liked about the RE-Amemiya was the lower half. The aggressiveness of the lower half of the RE-A bumper is what I loved. Hence My 20B FD has the RE-Amemiya N1-02 bumper. So, I fused the two together.
But what I did not like about either bumper is the center lower section raised. This caused a problem when wanting to use front splitter. So, we are making it flat.
Everything smooth out
And Mold being made.. (credit goes to LC Racing for making the mold).
Bumper is currently on my car and few things to be adjusted and new mold needs to be made.
#380
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
FUCKING SICK! Love the update dude
#381
Instructor
Thread Starter
#382
Instructor
Thread Starter
More Update...
No dip
I run an all rotary car event called, 'Deals Gap Rotary Rally' (www.DealsGapRotaryRally.com). Because this is almost 1000 mile journey at the end, I decided to dip portion of my front bumper to protect.
Event T-shirts
Video from my event
https://vimeo.com/126193813
After the event, I had a photoshoot with my friend Kenny Glover aka Super Model
These are photos I took of him taking photos.
Here are his photos
No dip
I run an all rotary car event called, 'Deals Gap Rotary Rally' (www.DealsGapRotaryRally.com). Because this is almost 1000 mile journey at the end, I decided to dip portion of my front bumper to protect.
Event T-shirts
Video from my event
https://vimeo.com/126193813
After the event, I had a photoshoot with my friend Kenny Glover aka Super Model
These are photos I took of him taking photos.
Here are his photos
The following users liked this post:
DaChef320 (07-28-2015)
#383
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
:fap:
#384
Team Owner
:fap fap fap:
#387
Instructor
Thread Starter
Update..
So, I drove to Atlanta for Import Alliance to be booth car for Grip Royal.
After the event, I went to Downtown ATL to do a shoot with Mike Kuhn and his girl Sami
Here are Mike's photos
So, I drove to Atlanta for Import Alliance to be booth car for Grip Royal.
After the event, I went to Downtown ATL to do a shoot with Mike Kuhn and his girl Sami
Here are Mike's photos
#389
Instructor
Thread Starter
More Update..
Just before my event, Deals Gap Rotary Rally (DGRR) (www.DealsGapRotaryRally.com), I got my seats back.
recovered Recaro RZ seats in grey suede
Installed in the car.
DGRR takes place in North Carolina/Tennessee and is one of the largest rotary car event in USA.
Its supported by the following sponsors
On my way it rained and when parked, I saw this
More photos from the event..
after the event, I got this box
Just before my event, Deals Gap Rotary Rally (DGRR) (www.DealsGapRotaryRally.com), I got my seats back.
recovered Recaro RZ seats in grey suede
Installed in the car.
DGRR takes place in North Carolina/Tennessee and is one of the largest rotary car event in USA.
Its supported by the following sponsors
On my way it rained and when parked, I saw this
More photos from the event..
after the event, I got this box
#390
Instructor
Thread Starter
More update..
Just before DGRR, I was asked by Speed Academy (Speed Academy) to do a write up about Plasti Dipping my FD. So, I've documented the process and they published it!
Go here to read the entire article.. Plasti Dip your car: Tips and tricks from a Pro | Speed Academy
Another photo.. from my event DGRR
Now that DGRR is over, I had approximately 3 weeks to get my car ready for the Exedy Booth at Formula Drift.. Also, I had a feature shoot with SpeedHunters.com
Its been my dream to be featured on SpeedHunters and one of my favorite photographer was going to shoot it, Larry Chen.
In 3 weeks, I'm going to install Turblown EWP kit, my new bumper, new color, new interior, etc.
To start, Turblown EWP kit (aka Davies Craig Electric Water pump)
I'm going to say this is one of the best mod I've done. Why?? Unlike other EWP kit I've seen, the controller will hold the pump from kicking in and pulse circulate during warm up, and once its fully warmed up, it will pump, when temp is too high, it will kick on the fans, and maintained the temp amazingly!! Another awesome feature is to continue to circulate the coolant and turn on the fan after engine is shut off.
Also, getting rid of air after filling the system with coolant was an ease. Just power the pump and fill!
Here is a video I did of the pump set up..
Just before DGRR, I was asked by Speed Academy (Speed Academy) to do a write up about Plasti Dipping my FD. So, I've documented the process and they published it!
Go here to read the entire article.. Plasti Dip your car: Tips and tricks from a Pro | Speed Academy
Another photo.. from my event DGRR
Now that DGRR is over, I had approximately 3 weeks to get my car ready for the Exedy Booth at Formula Drift.. Also, I had a feature shoot with SpeedHunters.com
Its been my dream to be featured on SpeedHunters and one of my favorite photographer was going to shoot it, Larry Chen.
In 3 weeks, I'm going to install Turblown EWP kit, my new bumper, new color, new interior, etc.
To start, Turblown EWP kit (aka Davies Craig Electric Water pump)
I'm going to say this is one of the best mod I've done. Why?? Unlike other EWP kit I've seen, the controller will hold the pump from kicking in and pulse circulate during warm up, and once its fully warmed up, it will pump, when temp is too high, it will kick on the fans, and maintained the temp amazingly!! Another awesome feature is to continue to circulate the coolant and turn on the fan after engine is shut off.
Also, getting rid of air after filling the system with coolant was an ease. Just power the pump and fill!
Here is a video I did of the pump set up..
#391
Turd Polisher
iTrader: (1)
I saw your dash kit on Instagram , nothing short of amazing!
#393
Moderator
Chapter Leader (South Florida Region)
Chapter Leader (South Florida Region)
iTrader: (6)
I hadn't clicked in a few of your updates. What a treat to read up on it now.
You've gotten insanely good at dipping the car!
Have you considered using a clear dip over the bumper/rear wheels to protect from chipping when you do end up going back to the oem paint?
You've gotten insanely good at dipping the car!
Have you considered using a clear dip over the bumper/rear wheels to protect from chipping when you do end up going back to the oem paint?
#394
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
great update...
Love the seats....that dry CF
#395
Instructor
Thread Starter
Thanks! Those seats are very comfortable too.
#396
Instructor
Thread Starter
More Update..
After my event DGRR 2015, I had a photoshoot with my friend and a photographer before I started to break down the car. I had at this point about 3 weeks til my photoshoot with SH.
Clean up my garage and hung my Exedy and Rays Engineering flags.
I than started working on the interior of the car. Replacing my old interior (CF) with all OE plastics with zero broken tabs.. and got them refinished.
With Spirit R cluster
Changed the Steering wheel to match the recovered RZ seats.
Changed out the Catback.. replaced the RE-Amemiya Dual Dolphine tips to Ganador full Titanium catback
Got my Defi BF gauges I had for severals years, got new sensors, wires, and tested them out.
New AutoEXE hood struts.
Full Function Engineering goodies
Some Carbon goodies...
Feed interior covers and Feed Ganador mirror cover in CF.
I been a fan of Samco Sport product since knowing Samco were first to produce OE upgrade rad and IC couplers and hoses. Mazdaspeed kit, Samco were the supplier for MS IS kit. So, i wanted to run their goods.
Ended up getting box full of Samco goodies..
And finally the bumper...
And Engine bay
After my event DGRR 2015, I had a photoshoot with my friend and a photographer before I started to break down the car. I had at this point about 3 weeks til my photoshoot with SH.
Clean up my garage and hung my Exedy and Rays Engineering flags.
I than started working on the interior of the car. Replacing my old interior (CF) with all OE plastics with zero broken tabs.. and got them refinished.
With Spirit R cluster
Changed the Steering wheel to match the recovered RZ seats.
Changed out the Catback.. replaced the RE-Amemiya Dual Dolphine tips to Ganador full Titanium catback
Got my Defi BF gauges I had for severals years, got new sensors, wires, and tested them out.
New AutoEXE hood struts.
Full Function Engineering goodies
Some Carbon goodies...
Feed interior covers and Feed Ganador mirror cover in CF.
I been a fan of Samco Sport product since knowing Samco were first to produce OE upgrade rad and IC couplers and hoses. Mazdaspeed kit, Samco were the supplier for MS IS kit. So, i wanted to run their goods.
Ended up getting box full of Samco goodies..
And finally the bumper...
And Engine bay
#397
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
I was surprised how comfy racing seats were too when I put mine in, and I went the cheap route with NRG...
holy moly those updates are awesome...its like a constant flow of updates haha....
can I ship my car to you for couple weeks and you can fix all the crap I have done with it?
holy moly those updates are awesome...its like a constant flow of updates haha....
can I ship my car to you for couple weeks and you can fix all the crap I have done with it?
#398
Instructor
Thread Starter
More Update..
I put all the new stuff on mainly to make it to my feature shoot with SpeedHunters. Unfortunately, I had about 3 weeks to pull it off but been working on it on the side for months.
I literally pulled it off the morning of the shoot.
Here are preview shots taken at the house, just before leaving to Road ATL.
My journey wasn't a pleasant one... My shoot with Larry Chen from Speedhunters was set at 4:30. I wanted to make sure I had plenty of time to get to ATL, avoid ATL traffic, goto my favorite restaurant for lunch, and have plenty of time to clean the car... as I drive this car to all the events.
So, Me and a local V8 FD owner who have never been to Formula Drift left my house around 8AM (9AM EST). As soon as we hit the main road, my car started to accelerate without my pushing the throttle, Since I changed up the several parts, I thought I might of not set the idle and such correctly.. After adjusting and stopping every exit on the interstate, I plugged in my laptop to the ECU to see what the possible issue was.. one of the great thing about Adaptronics ECU was you can reset/recalibrate the TPS. We reset and car seemed fine. Until 5-10 mins later it started to accelerate by itself again. At this point, me and my passenger had no idea what it was doing. Finally we got the car idling fine again and hit the road. Again it started to accelerate. Me and my passenger finally figured out, with the laptop, you can reset and recal the TPS on the fly. Everytime we reset, the car will stop accelerating. We ended up resetting the TPS over 100 times from Bham, AL to Road Atlanta. Our favorite was when we hit 3PM ATL traffic. One of the nerve wrecking drive I had was this drive. I would just shut the car off on the interstate as reset didn't help much. I had literally started the 20-30 times during the over an hour traffic I was stuck in.
At the end, I was amazed about two things I put in to this car,
1. Adaptronics ECU... the abilities to reset on the fly helped. Also, my laptop just plugging in and read the ECU without starting helped.
2. Turblown/Davies Craig Electric Water Pump (EWP). This thing truly worked. It was my first time running this kit and it truly did its job. During my ATL traffic off and on engine, I could hear the fans kicking in and waterpump circulating when engine was off. It kept my engine cool during this stressful time. Which one thing I didn't have to worry.
Oh, I forgot, I was also stranded on the interstate because my Aftermarket Industries (AI) surgetank went out. I was going 80MPH and all the sudden, car just dies. I was about to move from fast lane to right shoulder safely.
What I think it happened was, the fuel line I used inside the tank got undone. Luckily, when I was going from Radium single Bosch 044 to AI triple Walbro 440s, I had to extend some of the lines using brass barb fittings. Luckily, I was able to re route the lines so that I could use the stock pump instead of the AI tank. If I didn't use those barb fitting, we would of had to walk to the next exit, buy some fuel lines, and do all kind of fun stuff. Instead re routing took 15-20 mins and we were on the road.. still with acceleration issues.
We finally made it to Road ATL right around 4:15. I called Larry Chen asking where I needed to meet him and he said to just come down to the paddock. Going through the paddock, I felt little embarrassed. Mainly because car sounded horrible and I kept stalling out because it idled like ass.
When I met Larry, one of the thing he asked me was, "are you going to clean your car?". I guess he thought I was going to trailer the car and not drive what it was suppose to be 3 hour trip, now took 6+ hours. I told him to give me 10 mins.
I cleaned up the car as best as I could with my friend Michael, aka TPS resetter. and we went on the Road ATL for the shoot.
Here are some photos I took with my phone..
I'm now out of time.. I will update more later..
I put all the new stuff on mainly to make it to my feature shoot with SpeedHunters. Unfortunately, I had about 3 weeks to pull it off but been working on it on the side for months.
I literally pulled it off the morning of the shoot.
Here are preview shots taken at the house, just before leaving to Road ATL.
My journey wasn't a pleasant one... My shoot with Larry Chen from Speedhunters was set at 4:30. I wanted to make sure I had plenty of time to get to ATL, avoid ATL traffic, goto my favorite restaurant for lunch, and have plenty of time to clean the car... as I drive this car to all the events.
So, Me and a local V8 FD owner who have never been to Formula Drift left my house around 8AM (9AM EST). As soon as we hit the main road, my car started to accelerate without my pushing the throttle, Since I changed up the several parts, I thought I might of not set the idle and such correctly.. After adjusting and stopping every exit on the interstate, I plugged in my laptop to the ECU to see what the possible issue was.. one of the great thing about Adaptronics ECU was you can reset/recalibrate the TPS. We reset and car seemed fine. Until 5-10 mins later it started to accelerate by itself again. At this point, me and my passenger had no idea what it was doing. Finally we got the car idling fine again and hit the road. Again it started to accelerate. Me and my passenger finally figured out, with the laptop, you can reset and recal the TPS on the fly. Everytime we reset, the car will stop accelerating. We ended up resetting the TPS over 100 times from Bham, AL to Road Atlanta. Our favorite was when we hit 3PM ATL traffic. One of the nerve wrecking drive I had was this drive. I would just shut the car off on the interstate as reset didn't help much. I had literally started the 20-30 times during the over an hour traffic I was stuck in.
At the end, I was amazed about two things I put in to this car,
1. Adaptronics ECU... the abilities to reset on the fly helped. Also, my laptop just plugging in and read the ECU without starting helped.
2. Turblown/Davies Craig Electric Water Pump (EWP). This thing truly worked. It was my first time running this kit and it truly did its job. During my ATL traffic off and on engine, I could hear the fans kicking in and waterpump circulating when engine was off. It kept my engine cool during this stressful time. Which one thing I didn't have to worry.
Oh, I forgot, I was also stranded on the interstate because my Aftermarket Industries (AI) surgetank went out. I was going 80MPH and all the sudden, car just dies. I was about to move from fast lane to right shoulder safely.
What I think it happened was, the fuel line I used inside the tank got undone. Luckily, when I was going from Radium single Bosch 044 to AI triple Walbro 440s, I had to extend some of the lines using brass barb fittings. Luckily, I was able to re route the lines so that I could use the stock pump instead of the AI tank. If I didn't use those barb fitting, we would of had to walk to the next exit, buy some fuel lines, and do all kind of fun stuff. Instead re routing took 15-20 mins and we were on the road.. still with acceleration issues.
We finally made it to Road ATL right around 4:15. I called Larry Chen asking where I needed to meet him and he said to just come down to the paddock. Going through the paddock, I felt little embarrassed. Mainly because car sounded horrible and I kept stalling out because it idled like ass.
When I met Larry, one of the thing he asked me was, "are you going to clean your car?". I guess he thought I was going to trailer the car and not drive what it was suppose to be 3 hour trip, now took 6+ hours. I told him to give me 10 mins.
I cleaned up the car as best as I could with my friend Michael, aka TPS resetter. and we went on the Road ATL for the shoot.
Here are some photos I took with my phone..
I'm now out of time.. I will update more later..