SOLD: 20" Vossen CV3 Graphite Staggered
#1
Advanced
Thread Starter
20" Vossen CV3 Graphite Staggered
Category: Wheels & Tires
Price: $2500
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): RL 2G, TL 4G, ZDX
Location (State/Prov/Terr): NY
Item Condition: Used
Everything has less than 5k miles highway. I live in Pittsburgh, PA.
However the wheels are located at my brothers house in Bayside, NY. ( No Market for TL's in Pgh)
There is minor curb damaged located on the rear passenger wheel created by the village idiot (Me).
And minor chips from mounting the tires.
Front: 20x9 5x120 with Continental DWS Tires (245/35/20) 90% tread left
Rear: 20x10.5 5x120 with Continental DWS Tires (275/30/20) 90% tread left
Acura TPMS sensors will also be included along with Lugs and Hub Rings
Prefer local pick up
#2
Just a little info for those who don't know these are 5X120 wheels or what models use this size.
Fitment information for wheels with 5X120 bolt pattern. If this is a WTB, the information above will apply to the wheels needed to fit this application.
Standard 2G RL/4G TL wheels are 5X120, 17x8 with a +55 offset and 64.1 hub. Thread size 14X1.50.
These wheels, or the WTB wheels, only fit the following models, unless an adapter or spacer is used or the wheels are redrilled, because of the 5X120 bolt pattern and larger 14X1.50 studs and mounting holes: 4G (2009+) Acura TL, 2G (2005+) Acura RL, 2G (2007+) Acura MDX, Acura ZDX, Honda Odyssey, Honda Ridgeline, and 2009+ Honda Pilot.
3G TL wheels are 5x114.3, 17x8, +45 offset, thread size 12X1.50. All TSX and most other current Acura models are also 5X114.3 but with different width and offset.
If the wheels are not 17", the other dimensions should be similar, unless stated otherwise.
Fitment information for wheels with 5X120 bolt pattern. If this is a WTB, the information above will apply to the wheels needed to fit this application.
Standard 2G RL/4G TL wheels are 5X120, 17x8 with a +55 offset and 64.1 hub. Thread size 14X1.50.
These wheels, or the WTB wheels, only fit the following models, unless an adapter or spacer is used or the wheels are redrilled, because of the 5X120 bolt pattern and larger 14X1.50 studs and mounting holes: 4G (2009+) Acura TL, 2G (2005+) Acura RL, 2G (2007+) Acura MDX, Acura ZDX, Honda Odyssey, Honda Ridgeline, and 2009+ Honda Pilot.
3G TL wheels are 5x114.3, 17x8, +45 offset, thread size 12X1.50. All TSX and most other current Acura models are also 5X114.3 but with different width and offset.
If the wheels are not 17", the other dimensions should be similar, unless stated otherwise.
#4
Advanced
Thread Starter
PM's replied.. Shipping can be arranged at buyers expense but prefer local pick up. I'm not sure how to ship these. Unless I can find a big enough box for two wheels per box. Any suggestions?
#5
Drifting
iTrader: (1)
I sold a set of wheels a little while back and found a good way to package them.
I cut a piece of cardboard and some bubble wrap to cover the rim with (you'll need 6 circles of cardboard and 4 circles of bubble wrap). Then I put that cardboard and bubble wrap in between two of the wheels (rims facing each other with bubble wrap separating wheel from cardboard) and using two more pieces of cardboard cut in circles I covered the back side of the rims (which are now on the outside). I then wrapped each set of two in A LOT of shrink wrap (going both directions and overlapping). I shipped with UPS and the packages arrived with no issues.
See below for details. Hopefully this helps! GLWS!
*Shows cardboard covering the backside of rim.
*Shows wheel, bubble wrap, cardboard, bubble wrap, wheel.
*When wrapping with shrink wrap, be sure to go both directions. I rolled a lot first going with the tread, then cut it and started over going the opposite (i.e. perpendicular) direction.
I cut a piece of cardboard and some bubble wrap to cover the rim with (you'll need 6 circles of cardboard and 4 circles of bubble wrap). Then I put that cardboard and bubble wrap in between two of the wheels (rims facing each other with bubble wrap separating wheel from cardboard) and using two more pieces of cardboard cut in circles I covered the back side of the rims (which are now on the outside). I then wrapped each set of two in A LOT of shrink wrap (going both directions and overlapping). I shipped with UPS and the packages arrived with no issues.
See below for details. Hopefully this helps! GLWS!
*Shows cardboard covering the backside of rim.
*Shows wheel, bubble wrap, cardboard, bubble wrap, wheel.
*When wrapping with shrink wrap, be sure to go both directions. I rolled a lot first going with the tread, then cut it and started over going the opposite (i.e. perpendicular) direction.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
neuronbob
3G RLX Tires, Wheels & Suspension
23
07-16-2019 10:48 AM