KK's modded WDP Sh Awd with Rotora BBK
07-17-2014, 12:16 AM
#681
The Original Shawdy
Haha that Tein ratchet is pretty clever. Be good for show.
07-21-2014, 07:52 PM
#682
Your car is amazing sir. Only had tine to look at page 1 before typing this out. I recently oredered 3k HID Fogs for my TL. I also have a 2010 WDP SH-AWD.
So far I have Debadged all but the center Acura Emblem on the trunk. Tinted car with cermaic 18% all around accept windshield which is 50% ceramic. Going to continue to read your entire page.
Questions so far...
Has your back window lip still held up good and paint is true to rest of car?
Where you get the DRL LEDs? are they still holding up?
I went on http://www.teamsls.ca/ to find the pedals but have had no luck...any help on where to locate on website?
Keep it up and thanks for sharing your hard work.
So far I have Debadged all but the center Acura Emblem on the trunk. Tinted car with cermaic 18% all around accept windshield which is 50% ceramic. Going to continue to read your entire page.
Questions so far...
Has your back window lip still held up good and paint is true to rest of car?
Where you get the DRL LEDs? are they still holding up?
I went on http://www.teamsls.ca/ to find the pedals but have had no luck...any help on where to locate on website?
Keep it up and thanks for sharing your hard work.
The following users liked this post:
KarKraze (07-21-2014)
07-21-2014, 08:40 PM
#683
Drifting
Thread Starter
Your car is amazing sir. Only had tine to look at page 1 before typing this out. I recently oredered 3k HID Fogs for my TL. I also have a 2010 WDP SH-AWD.
So far I have Debadged all but the center Acura Emblem on the trunk. Tinted car with cermaic 18% all around accept windshield which is 50% ceramic. Going to continue to read your entire page.
Questions so far...
Has your back window lip still held up good and paint is true to rest of car?
Where you get the DRL LEDs? are they still holding up?
I went on http://www.teamsls.ca/ to find the pedals but have had no luck...any help on where to locate on website?
Keep it up and thanks for sharing your hard work.
So far I have Debadged all but the center Acura Emblem on the trunk. Tinted car with cermaic 18% all around accept windshield which is 50% ceramic. Going to continue to read your entire page.
Questions so far...
Has your back window lip still held up good and paint is true to rest of car?
Where you get the DRL LEDs? are they still holding up?
I went on http://www.teamsls.ca/ to find the pedals but have had no luck...any help on where to locate on website?
Keep it up and thanks for sharing your hard work.
Thank you for your kind words, really appreciate it.
To answer your questions, the rear window trim is holding up quite well so far, no discolouration or other paint damage. Very happy with it.
The DRls were purchased from http://store.ijdmtoy.com/ and I have had no issues to date with them.
It is possible that I was actually the first to post the pedals up and I did get the from Team Sls, however you can get them here and it is the best price I have seen so far
http://www.aliexpress.com/item/Sport...314047573.html
I am not sure if it is the same quality as mine but for the price it is worth it.
Let me know if you have any further questions and good luck with your mods.
07-22-2014, 05:53 PM
#684
Team Owner
iTrader: (2)
Join Date: Jan 2008
Location: Kansas City, MO (Overland Park, KS)
Posts: 36,545
Received 6,470 Likes
on
5,162 Posts
KK, sorry I haven't visited in a while. The new shots look great.
The following users liked this post:
KarKraze (07-23-2014)
08-06-2014, 06:14 PM
#686
Team Owner
iTrader: (2)
Join Date: Jan 2008
Location: Kansas City, MO (Overland Park, KS)
Posts: 36,545
Received 6,470 Likes
on
5,162 Posts
Beautiful shots.
08-07-2014, 08:41 PM
#689
Drifting
Thread Starter
But that C7 of yours though
thank you, it was sunrise.Thanks, tell me more about your avatar
Should have some new mods coming soon, working on it but will see if the results are worth posting .
Last edited by KarKraze; 08-07-2014 at 08:44 PM.
The following users liked this post:
KarKraze (08-08-2014)
08-10-2014, 09:12 PM
#691
Drifting
Thread Starter
So here is the beginning of a little project that I wanted to do for a while, managed to get my hands on a left side taillight and want to cut it open. I would like to black out the silver trim, tint the clear indicator red and leave a small clear for the reverse lights.
I am well aware that I can just do the vinyl tint that everyone else does or I can contact JNC and purchase a set of lights done the way I wanted it, that however would be no fun.
Couple of things you will need for this part of the project
1) Safety Glass or face shield
2) Long sleeve shirt
3) Dremmel tool and some cutting tips
4) Masking tape
5) Taillight
6) Patience and steady hands.
I am well aware that I can just do the vinyl tint that everyone else does or I can contact JNC and purchase a set of lights done the way I wanted it, that however would be no fun.
Couple of things you will need for this part of the project
1) Safety Glass or face shield
2) Long sleeve shirt
3) Dremmel tool and some cutting tips
4) Masking tape
5) Taillight
6) Patience and steady hands.
The following 3 users liked this post by KarKraze:
08-12-2014, 07:04 PM
#692
Team Owner
iTrader: (2)
Join Date: Jan 2008
Location: Kansas City, MO (Overland Park, KS)
Posts: 36,545
Received 6,470 Likes
on
5,162 Posts
Nice....
08-12-2014, 09:25 PM
#693
Drifting
Thread Starter
I haven't had much time to do anything else but I found out something that I didn't know. The back of the outer clear lens has a protective coating, I assume it is UV related.
The coating is at the back of this piece after the red lens are removed
Also, I am in the market for a right side tail light in order to complete the project. Hit me with a PM if anyone has one in working condition.
The coating is at the back of this piece after the red lens are removed
Also, I am in the market for a right side tail light in order to complete the project. Hit me with a PM if anyone has one in working condition.
Last edited by KarKraze; 08-12-2014 at 09:29 PM.
08-13-2014, 08:09 AM
#694
rock the block
looks great kk, very original idea. I'd love to see the finished product.
once this is successful, maybe i will have you do mine :P
speaking of which, how did the headlight clearing go a few weeks ago?
once this is successful, maybe i will have you do mine :P
speaking of which, how did the headlight clearing go a few weeks ago?
08-17-2014, 07:07 PM
#697
Drifting
Thread Starter
The adjuster is just something that was done on a whim,its not a priority because i am happy with the current setting.
Last edited by KarKraze; 08-17-2014 at 07:10 PM.
08-17-2014, 07:16 PM
#698
Drifting
Thread Starter
...............and since i am working on rear lights,it seems like the perfect time to address another thing i didn't like about the rear end.....the overly large reflectors!
.
.
08-19-2014, 06:59 PM
#700
Drifting
Thread Starter
So basically i went from stock as shown
to this after opening it up
one more to go then installation. The reason i am doing this is to tone down the rear end,i may also do a partial debadge but will decide on that after i have the lights done and installed.
to this after opening it up
one more to go then installation. The reason i am doing this is to tone down the rear end,i may also do a partial debadge but will decide on that after i have the lights done and installed.
Last edited by KarKraze; 08-19-2014 at 07:09 PM.
08-19-2014, 07:46 PM
#702
Drifting
Thread Starter
Ahaha, i just realized that you are talking about the lower reflectors,sorry.
Yes, i have a border around it. Will see how it all come together when everything is completed.
Last edited by Steven Bell; 08-23-2014 at 04:23 PM.
The following users liked this post:
KarKraze (08-21-2014)
08-23-2014, 04:23 PM
#705
Team Owner
iTrader: (2)
Join Date: Jan 2008
Location: Kansas City, MO (Overland Park, KS)
Posts: 36,545
Received 6,470 Likes
on
5,162 Posts
Dude....those look great. When's install?
The following users liked this post:
KarKraze (09-06-2014)
09-06-2014, 05:51 PM
#707
The Original Shawdy
They do look pretty clean. Be nice on CBP. I was never a fan of tinted taillights it the blacked out reflectors look nice.
Great work like always!
Great work like always!
The following users liked this post:
KarKraze (09-12-2014)
09-09-2014, 12:42 PM
#709
Beautiful mod KK, they look super clean.
Seems like a lot of work but the results speak for itself. I don't mind the vinyl tint but this is leaps and bounds beyond that.
Seems like a lot of work but the results speak for itself. I don't mind the vinyl tint but this is leaps and bounds beyond that.
Last edited by ALFAQ; 09-09-2014 at 12:50 PM.
09-09-2014, 05:22 PM
#711
Drifting
Thread Starter
Thanks my friend, the other light should be here by Friday.Hopefully i can work on it this weekend.
Been very busy lately,burning the candle at both ends working Sunday to Sunday lol.
Thank you,i will post more pics as i make progress,i will be putting the car away in a few weeks but will try to wrap it up before.
09-09-2014, 06:01 PM
#712
Drifting
Thread Starter
These were taken the same evening as the previous pictures and gives a comparison between the silver bezel and the black that i am working on.
Once i have the right side completed and installed i will also do a partial debadge to clean up the rear some more.
Once i have the right side completed and installed i will also do a partial debadge to clean up the rear some more.
09-09-2014, 08:24 PM
#713
Team Owner
iTrader: (2)
Join Date: Jan 2008
Location: Kansas City, MO (Overland Park, KS)
Posts: 36,545
Received 6,470 Likes
on
5,162 Posts
Sweet!
The following users liked this post:
KarKraze (09-12-2014)
09-10-2014, 10:59 AM
#716
The Original Shawdy
Flows really nice with with the tinted reflectors. They look really slimmed down, never liked the oversized reflectors on the 09-11. But yours are clean!
The following users liked this post:
KarKraze (09-12-2014)
09-12-2014, 10:49 PM
#719
did you install the ice box???
i like how those tail lights look! i wonder if you could have got a similar look by just spraying them with a smoke tint on the outside??? on a former car, I had the tails sprayed..and they ended up looking similar to yours.. a light coat leave sthem looking red but with that dark smoked look....
overall, i like the rear end. that black border on the reflectors kind of looks nice..since you blacked the tail ligths it all works
i like how those tail lights look! i wonder if you could have got a similar look by just spraying them with a smoke tint on the outside??? on a former car, I had the tails sprayed..and they ended up looking similar to yours.. a light coat leave sthem looking red but with that dark smoked look....
overall, i like the rear end. that black border on the reflectors kind of looks nice..since you blacked the tail ligths it all works
09-13-2014, 07:51 AM
#720
Drifting
Thread Starter
did you install the ice box???
i like how those tail lights look! i wonder if you could have got a similar look by just spraying them with a smoke tint on the outside??? on a former car, I had the tails sprayed..and they ended up looking similar to yours.. a light coat leave sthem looking red but with that dark smoked look....
overall, i like the rear end. that black border on the reflectors kind of looks nice..since you blacked the tail ligths it all works
i like how those tail lights look! i wonder if you could have got a similar look by just spraying them with a smoke tint on the outside??? on a former car, I had the tails sprayed..and they ended up looking similar to yours.. a light coat leave sthem looking red but with that dark smoked look....
overall, i like the rear end. that black border on the reflectors kind of looks nice..since you blacked the tail ligths it all works
I replied to your previous question about the performance of it,not sure if your saw it or not. You can feel better throttle response throughout the entire rev range and i am happy with it.
I didn't want to spray the outside of the lens due to the possibility of scratches etc,didn't mind the vinyl tint either. I feel that the way i did it gives it a factory appearance rather than an add on.
It was a lot of work and the possibility of other issues exist,time will reveal its durability.However,for now, i am extremely satisfied with the finished product and that is coming from someone who is very meticulous about the way things are done.
Pics of the end results will be coming soon.
Last edited by KarKraze; 09-13-2014 at 07:53 AM.