its official! introducing....jeroplex!
#81
I went with 1 finger gap all around. It settles a bit after a week to just sitting right on top of the tire. Its as low as I am willing to go. my nose is centimeters away from scraping asphalt on even moderate rolled curbs at the end of driveways.
#83
Burning Brakes
Thread Starter
tire is just sitting right above the fender. i think this might be tooooo low. lol when i turn the wheel too much it starts to rub on the fender i dont think that can be fixed from fender rolling or can it? also as it sits now the fenders arent rolled but if i were to get an alignment i would need to roll right? since the wheels will straighten out?
#84
Burning Brakes
I'm usually not a fan of the "slammed" look, but with those rims, it looks pretty darn nice.
#86
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
need moar pix.....
looking goood so far....
looking goood so far....
#88
Three Wheelin'
tire is just sitting right above the fender. i think this might be tooooo low. lol when i turn the wheel too much it starts to rub on the fender i dont think that can be fixed from fender rolling or can it? also as it sits now the fenders arent rolled but if i were to get an alignment i would need to roll right? since the wheels will straighten out?
#89
Burning Brakes
Thread Starter
I will for sure ..thx
thanks
yea fronts are rubbing when I turn the wheel to a certain point. I don't think I can complete a sharp u turn. So the fronts can't be rolled any further than what they are at? How about if I were to raise it half inch or finger gap u think it will still rub?
thanks
Props Bro! That's a nice set up. I assume the the rubbing of the fenders is in the front and not the rear? If that's the case, rolling the fender will not work since the fronts are already rolled. You can either have the wheels machined down a few millimeters or install the adjustable ball joints and add a couple degrees of negative camber. Hope it all works out! Gotta love PWPs on baller rims
#90
Three Wheelin'
Raising will help if you don't expect your front suspension to travel much. The problem is not the ride height. It's a combination of the tires and wheel offset being a bit too aggressive.
#91
Burning Brakes
Thread Starter
damn thats what i wanted to avoid. i thought i pretty safe with +40 offset..... well now i tried to turn the wheel and it didnt rub and i was able to turn it all the way but it was parked. i might have to raise it a little once it settles. only reason is i dont want to eff up my fender. when you say "Raising will help if you don't expect your front suspension to travel much" do you mean travel distance it will move while im driving? the rubbing when i turn ive only tested when i was parked havent did a full turn while drive to see
Last edited by jeroplex; 11-12-2011 at 09:03 AM.
The following users liked this post:
jeroplex (11-12-2011)
#95
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
looks great bro....
i still feel rear needs spacers and you need to run a little neg chamber with those rims + drop....
i still feel rear needs spacers and you need to run a little neg chamber with those rims + drop....
The following users liked this post:
swoosh (11-12-2011)
#98
Nice man. Yeah saw the picture of your front fender sitting on your tire. Props for slamming it . Tell me how the fender roll goes. I'll be getting mine rolled sometime in the near future. Got some new wheels coming in the mail.
#99
Burning Brakes
Thread Starter
anyone have experience with alignments from firestone?
http://www.firestonecompleteautocare.../alignment.jsp
http://www.firestonecompleteautocare.../alignment.jsp
#100
takin care of Business in
iTrader: (5)
Join Date: Jan 2008
Location: Kansas City, MO
Age: 40
Posts: 30,994
Received 4,732 Likes
on
4,064 Posts
^^^ I do....they are fucking awesome !!!
Condition: Find one which is newly opened....so they have a brand new alignement rack....this ones goes underground so driving on it is very simple....awesome for lowered/slammed cars....If they have the old rack where you have to drive up, it gonna take them an hour just to get on and off the ramp and they gonna scrape all under ur car....
I have their lifetime alignment for $160....i took the girl at the counter out for dinner and found a 50% discount coupon hidden in her clothes ....didnt really save me money coz the dinner was more expensive than the 50% coupon
I get my car aligned and my tires rotated/balanced every 5K miles when I do my oil change.....
Condition: Find one which is newly opened....so they have a brand new alignement rack....this ones goes underground so driving on it is very simple....awesome for lowered/slammed cars....If they have the old rack where you have to drive up, it gonna take them an hour just to get on and off the ramp and they gonna scrape all under ur car....
I have their lifetime alignment for $160....i took the girl at the counter out for dinner and found a 50% discount coupon hidden in her clothes ....didnt really save me money coz the dinner was more expensive than the 50% coupon
I get my car aligned and my tires rotated/balanced every 5K miles when I do my oil change.....
The following users liked this post:
spongebill (11-13-2011)
The following users liked this post:
jeroplex (11-13-2011)
The following users liked this post:
ed_423 (11-13-2011)
#105
jgarcia lol!
#108
Burning Brakes
Thread Starter
The front is really close to the top fender already. The back could but I'm not going to just yet. Going to get the back rolled tomorrow the front looks factory rolled not sure if it can roll any further
#111
Burning Brakes
Thread Starter
you might wnat to check these guys out in sanford.
http://www.performanceracesolutions.com/home.php
even the shop samules i went to might even roll them.
http://www.samuelsauto.com/
Last edited by jeroplex; 11-17-2011 at 06:03 PM.
The following users liked this post:
swarlos (11-17-2011)
#112
i did get them rolled by them.... dont go to them to get them rolled. they didnt do the greatest job. i am going to go to sanford to a shop called samules to just have them trim or cut my rear fender.i dont wnat to drive to kissismme and deal with them about it. speedzone for some reason when they did it (noticed this later on) that my paint in the inner part was chipped or cracked on both rears. i guess thats why it was cheap. Also when terry from samules looked at my quarter panels notice that they werent normal kinda bent or dented a little. But just a heads up i wouldnt recommend you go to them to get it rolled
Also, just as an FYI, do some research (if you have not already) on trimming/cutting the fenders. I remember seeing some info about rusting issues that may occur with that method.
eh. now I'm spooked about fitting my 9.5s.
#113
Burning Brakes
Thread Starter
Shit! I'm sorry to hear that. I thought they knew what they were doing...That makes me mad Hope you find a good fix and thanks for the heads up.
Also, just as an FYI, do some research (if you have not already) on trimming/cutting the fenders. I remember seeing some info about rusting issues that may occur with that method.
eh. now I'm spooked about fitting my 9.5s.
Also, just as an FYI, do some research (if you have not already) on trimming/cutting the fenders. I remember seeing some info about rusting issues that may occur with that method.
eh. now I'm spooked about fitting my 9.5s.
#114
Hmm. makes sense that as long as they paint and clear the areas that they cut, you should remain rust free.
#115
Burning Brakes
Thread Starter
thats the plan...and they arent cutting it totally. i think about half of what the original fender was. are you kevin btw? lol vishal as speedzone mentioned a guy named kevin with a second gen tsx at their shop
#117
cutting fenders..interesting. Hope it goes well man!
#118
I think I'm gonna try this shop in Tampa Called S&R performance to get my fenders rolled. Been seeing a lot of good reviews.
Last edited by swarlos; 11-17-2011 at 08:39 PM.
#119
Instructor
iTrader: (1)
you dont cut fenders on acuras and hondas. if you feel your quarter panels they have pinch welds in them. (feels like ingraved spots) you cut them and your panels are going to split. you can do that for vws and im pretty sure that the shop your planning to go to is a euro shop.
lol tommy please dont do anything stupid on your car. one of michaels friends 1st gen tsx did the same thing and you can see through it rofl.
i work in a body shop as a painter and i know what i am talking about not blowing smoke up your ass.
lol tommy please dont do anything stupid on your car. one of michaels friends 1st gen tsx did the same thing and you can see through it rofl.
i work in a body shop as a painter and i know what i am talking about not blowing smoke up your ass.
#120
Burning Brakes
Thread Starter
who is tommy? how can i know if there are pitch welds or are you saying they do? also i would be cutting just the rears not the front if that matters?
Last edited by jeroplex; 11-18-2011 at 05:52 AM.