Cheapest place to buy body kits in NYC or Philly
#1
Burning Brakes
Thread Starter
Join Date: Sep 2000
Location: New York City
Age: 47
Posts: 973
Likes: 0
Received 0 Likes
on
0 Posts
![Post](https://acurazine.com/forums/images/icons/icon1.gif)
Does anyone know where I can get Acura Body kits installed cheaper than the dealer in NYC or Philly?
I found a place in PA at A&H Motors and its only $800-not including install.
I found a place in PA at A&H Motors and its only $800-not including install.
#2
Senior Moderator
iTrader: (2)
Join Date: May 2000
Location: where the weather suits my clothes
Age: 55
Posts: 27,921
Received 1,080 Likes
on
661 Posts
![Post](https://acurazine.com/forums/images/icons/icon1.gif)
Originally posted by Mstyle:
Does anyone know where I can get Acura Body kits installed cheaper than the dealer in NYC or Philly?
I found a place in PA at A&H Motors and its only $800-not including install.
Does anyone know where I can get Acura Body kits installed cheaper than the dealer in NYC or Philly?
I found a place in PA at A&H Motors and its only $800-not including install.
------------------
1999 Satin Silver Metallic 3.2 TL w/o Navigation
- 18x8 Racing Hart C2s with Dunlop SP Sport 9000 225/40ZR18
- Comptech springs, sways, exhaust, and headers
- Red AEM CAI
- Factory underbody kit and spoiler
- Clifford Intelliguard 9000 alarm
- Alpine 6 disk CD changer
- Burlwood shift knob
- Trunk tray
- 20% tint
#3
Burning Brakes
Thread Starter
Join Date: Sep 2000
Location: New York City
Age: 47
Posts: 973
Likes: 0
Received 0 Likes
on
0 Posts
![Post](https://acurazine.com/forums/images/icons/icon1.gif)
Thanks NSX I heard it wasn't hard.. But I heard you have to take off your front bumper is that true???
How long did it take you to install
How long did it take you to install
#4
Senior Moderator
iTrader: (2)
Join Date: May 2000
Location: where the weather suits my clothes
Age: 55
Posts: 27,921
Received 1,080 Likes
on
661 Posts
![Post](https://acurazine.com/forums/images/icons/icon1.gif)
No, but you do have to take off the front lip piece that attaches to the bottom of the bumper. If you look at the bottom of the bumper, there is a notch that runs all the way around. There are actually two pieces to the bumper. The bottom piece comes off and is replaced by the underbody kit. Same for the rear bumper. The sides completely replace the current side pieces.
If you can follow directions it's not that bad. Give yourself a day to do it. I would also wait till it warms up. The plastic clips that hold everything in are a little brittle and Acura will rape you on the cost if you need to buy a few of them.
Good luck.
------------------
1999 Satin Silver Metallic 3.2 TL w/o Navigation
If you can follow directions it's not that bad. Give yourself a day to do it. I would also wait till it warms up. The plastic clips that hold everything in are a little brittle and Acura will rape you on the cost if you need to buy a few of them.
Good luck.
------------------
1999 Satin Silver Metallic 3.2 TL w/o Navigation
- 18x8 Racing Hart C2s with Dunlop SP Sport 9000 225/40ZR18
- Comptech Springs, Sways, Exhaust, and Headers
- Red AEM CAI
- Factory Underbody Kit and Spoiler
- Clifford Intelliguard 9000 alarm
- Alpine 6 disk CD changer
- Burlwood shift knob
- Trunk tray
- 20% tint
Trending Topics
#9
Safety Car
Join Date: Sep 2000
Location: Milky Way, Earth
Posts: 3,806
Likes: 0
Received 0 Likes
on
0 Posts
![Post](https://acurazine.com/forums/images/icons/icon1.gif)
The front lip is hard to get off - you have to take off the bumper cover, or do like I did and just cut the bisnatch off.
The rear stays, the kit goes on over it. The sides are easy once you understand how to do them, look in the instructions forum for my post.
![](http://www.acura-tl.com/ubb/smile.gif)
#11
Senior Moderator
iTrader: (2)
Join Date: May 2000
Location: where the weather suits my clothes
Age: 55
Posts: 27,921
Received 1,080 Likes
on
661 Posts
![Post](https://acurazine.com/forums/images/icons/icon1.gif)
Originally posted by Nate:
The front lip is hard to get off - you have to take off the bumper cover, or do like I did and just cut the bisnatch off.
The rear stays, the kit goes on over it. The sides are easy once you understand how to do them, look in the instructions forum for my post.
The front lip is hard to get off - you have to take off the bumper cover, or do like I did and just cut the bisnatch off.
![](http://www.acura-tl.com/ubb/smile.gif)
Sorry to disagree with you but, DO NOT TAKE OFF THE FRONT BUMPER. You just need to remove the lower piece of the bumper. It's held together with several of those plastic screw-in clips.
------------------
1999 Satin Silver Metallic 3.2 TL w/o Navigation
- 18x8 Racing Hart C2s with Dunlop SP Sport 9000 225/40ZR18
- Comptech Springs, Sways, Exhaust, and Headers
- Red AEM CAI
- A'PEXi Digital VTEC AFC
- Factory Underbody Kit and Spoiler
- Clifford Intelliguard 9000 alarm
- Alpine 6 disk CD changer
- BEL 945i Cordless Radar Detector
- Burlwood shift knob
- Trunk tray
- 20% tint
Thread
Thread Starter
Forum
Replies
Last Post
Zonian22
Member Cars for Sale
3
11-14-2015 01:20 PM
Yumcha
Automotive News
2
09-04-2015 08:03 AM
Zonian22
Member Cars for Sale
1
09-02-2015 08:19 AM