Clutch Damper Bypass-CLS-6
#43
Unregistered user
iTrader: (2)
Originally Posted by Allout
You have to bleed it at the slave cylinder using the bleed screw (see #1 on the illustration). Clutch pipe B connects to the slave cylinder.
http://www.acuraoemparts.com/delray/...All&vinsrch=no
http://www.acuraoemparts.com/delray/...All&vinsrch=no
also, bleeding the clutch "wastes" a lot of clutch fluid correct? i would have to fill it up a lot for bleeding it.
#46
Blown is Best
Attach one end of the hose to the end of the bleed screw and place the other end of the hose in a jar to collect the fluid. If you don't use a hose, you'll just spray fluid all over the place.
#47
Blown is Best
Originally Posted by SkillOBskilled
What do you guys think of getting a replacement B pipe and bending it to make a direct connection between the slave and the clutch? Is it long enough?
#48
Originally Posted by fuzzy02CLS
The point of this mod is to loose the dampener. You should at least try it. Why do the work?
#49
'03 ABP YA4-S 6MT
Join Date: Mar 2007
Location: Edmonton, AB
Age: 37
Posts: 1,192
Likes: 0
Received 18 Likes
on
18 Posts
the damper is there for warranty issues, mainly.
as is it said before, there are also negative effects to having it, such as slower takeup on the clutch = higher wear, *indirect* feeling on the friction point, etc..
http://www.zeckhausen.com/CDV.htm
as is it said before, there are also negative effects to having it, such as slower takeup on the clutch = higher wear, *indirect* feeling on the friction point, etc..
http://www.zeckhausen.com/CDV.htm
#51
Team Owner
iTrader: (1)
Join Date: Sep 2002
Location: Fontana, California
Age: 47
Posts: 30,991
Received 582 Likes
on
346 Posts
Originally Posted by fuzzy02CLS
Not to mention every time I I shift fast at red line from 1-2 & 2-3 I get clutch grinding.
Both 6 speeds I had did it.
Both 6 speeds I had did it.
#53
Originally Posted by fuzzy02CLS
Not to mention every time I I shift fast at red line from 1-2 & 2-3 I get clutch grinding.
Both 6 speeds I had did it.
Both 6 speeds I had did it.
#63
Blown is Best
Originally Posted by rp_guy
alright. i suggest you put some pb blaster or liquid wrench on it before you start. i stripped the bolt to the b pipe and now i have to buy a new line (~$10)
#64
Senior Moderator
iTrader: (2)
This may be a dumb question......
How do you get this out? The service manual is vague at best. I have the car on car ramps. I don't have access to a lift anymore.
I see it, but I don't seem to have any room under the car to get to it. Can it be done from the top?
I can't get the car any higher currently.
How do you get this out? The service manual is vague at best. I have the car on car ramps. I don't have access to a lift anymore.
I see it, but I don't seem to have any room under the car to get to it. Can it be done from the top?
I can't get the car any higher currently.
#66
'03 ABP YA4-S 6MT
Join Date: Mar 2007
Location: Edmonton, AB
Age: 37
Posts: 1,192
Likes: 0
Received 18 Likes
on
18 Posts
there is WAYYYY more access from the top. i don't even think you can do it from the bottom.
but yes, a flare nut wrench is probably a very good idea. i did not know this and the new line is actually $20 ! argh !
but yes, a flare nut wrench is probably a very good idea. i did not know this and the new line is actually $20 ! argh !
#67
Senior Moderator
iTrader: (2)
Ok top it is. I got the car off the ramps, I took the intake tube off & I loosened the nuts with the 10mm flare nut wrench. I have not pulled anything apart yet.
So I need more help. The little clips, are they supposed to come off before you unscrew the hard line? Or after?
So I'm putting 1 hard line into the new SS line from the slave & the other hard line into the other end from the master cylinder? Then routing the new line out of the way? Is that right?
The left over parts should be a little u shaped hard line & the dampener?
So I need more help. The little clips, are they supposed to come off before you unscrew the hard line? Or after?
So I'm putting 1 hard line into the new SS line from the slave & the other hard line into the other end from the master cylinder? Then routing the new line out of the way? Is that right?
The left over parts should be a little u shaped hard line & the dampener?
#71
Unregistered user
iTrader: (2)
oh yeah forgot to report my install:
i jacked up the car thinking the damper would be under the car on the front driver side since that's where it was for my buddy's e46. i searched for about 10 minutes. damn i felt dumb. went back to this thread and studied the diagram for a bit then finally figured it out. i couldn't secure the new SS line where the original one was but i don't think it's a big deal.
anyways after i properly wasted my bottle of clutch fluid (i also figured out that clutch fluid is the same as brake fluid dot 3 or 4) and bleed my clutch it was firmer which was what i was aiming for. for some reason my clutch turned soft (before CDD bypass).
i jacked up the car thinking the damper would be under the car on the front driver side since that's where it was for my buddy's e46. i searched for about 10 minutes. damn i felt dumb. went back to this thread and studied the diagram for a bit then finally figured it out. i couldn't secure the new SS line where the original one was but i don't think it's a big deal.
anyways after i properly wasted my bottle of clutch fluid (i also figured out that clutch fluid is the same as brake fluid dot 3 or 4) and bleed my clutch it was firmer which was what i was aiming for. for some reason my clutch turned soft (before CDD bypass).
#75
Blown is Best
Originally Posted by LIPPSTUH
i tried using a socket, there is not enough room to clear it.
i suggest having a second person help refill it since it leaks FAST.
i suggest having a second person help refill it since it leaks FAST.
#77
'03 ABP YA4-S 6MT
Join Date: Mar 2007
Location: Edmonton, AB
Age: 37
Posts: 1,192
Likes: 0
Received 18 Likes
on
18 Posts
successfully bypassed the CDD !!!
if anyone wants to remove the CDD without buying a new line, you can easily reuse the stock rubber line.. you don't need to cut any brackets or anything like that. i probably only used about 200mL of brake fluid to flush the line.
my shifts are 100% smoother now =D
if anyone wants to remove the CDD without buying a new line, you can easily reuse the stock rubber line.. you don't need to cut any brackets or anything like that. i probably only used about 200mL of brake fluid to flush the line.
my shifts are 100% smoother now =D
#78
Senior Moderator
iTrader: (2)
I'm done too.
Besides the pedal feeling a tad different, I see no difference. Feels like any other clutch pedal to me. I still get some grinding going into 2nd at redline on a fast shift. I'll drive it for a week & see.
BTW the TL clutch line HNC-009 fits fine. Actually any SS line with the right fittings will work. It only needs to be about 4".
Besides the pedal feeling a tad different, I see no difference. Feels like any other clutch pedal to me. I still get some grinding going into 2nd at redline on a fast shift. I'll drive it for a week & see.
BTW the TL clutch line HNC-009 fits fine. Actually any SS line with the right fittings will work. It only needs to be about 4".
#79
Originally Posted by fuzzy02CLS
I'm done too.
Besides the pedal feeling a tad different, I see no difference. Feels like any other clutch pedal to me. I still get some grinding going into 2nd at redline on a fast shift. I'll drive it for a week & see.
BTW the TL clutch line HNC-009 fits fine. Actually any SS line with the right fittings will work. It only needs to be about 4".
Besides the pedal feeling a tad different, I see no difference. Feels like any other clutch pedal to me. I still get some grinding going into 2nd at redline on a fast shift. I'll drive it for a week & see.
BTW the TL clutch line HNC-009 fits fine. Actually any SS line with the right fittings will work. It only needs to be about 4".
#80
MP90 uninstalled
I have a new tranny and removed the clutchdamper also. I have noticed that it hooks up a little better when abused. I have got the second gear grind once since doing the change