Milano Red TSX w/ 18x8 Work VS-SS rims
#1
Burning Brakes
Thread Starter
Milano Red TSX w/ 18x8 Work VS-SS rims
Here's some updated pics of my MR 05 TSX w/ 18x8 Work VS-SS +51 offset rims and 235-40-18 Yokohama ES100 tires.
It's lowered on Neuspeed Koni shocks + Comptech 110-155 springs. In these pictures, the spring perch is set at 1 notch below the middle at all 4 corners or 1/4" lower than what the typical Comptech 110-155 drop would look like.
No tire rubbing issues at all thus far.
I'm still debating on whether I should go with the Euro-R bodykit or the US OEM kit.
![](http://img79.echo.cx/img79/4125/p10108894sy.jpg)
![](http://img17.echo.cx/img17/1451/p10108942kx.jpg)
![](http://img79.echo.cx/img79/7960/p10108098uz.jpg)
Here's a close up shot of the wheel well gap in the front:
![](http://img79.echo.cx/img79/6025/dscn96771go.jpg)
And a shot of the wheel well gap in the rear:
It's lowered on Neuspeed Koni shocks + Comptech 110-155 springs. In these pictures, the spring perch is set at 1 notch below the middle at all 4 corners or 1/4" lower than what the typical Comptech 110-155 drop would look like.
No tire rubbing issues at all thus far.
I'm still debating on whether I should go with the Euro-R bodykit or the US OEM kit.
![](http://img79.echo.cx/img79/4125/p10108894sy.jpg)
![](http://img17.echo.cx/img17/1451/p10108942kx.jpg)
![](http://img79.echo.cx/img79/7960/p10108098uz.jpg)
Here's a close up shot of the wheel well gap in the front:
![](http://img79.echo.cx/img79/6025/dscn96771go.jpg)
And a shot of the wheel well gap in the rear:
![](http://img300.echo.cx/img300/6223/dscn96765rj.jpg)
#2
Rep'n Taxbrain.com
Join Date: Aug 2004
Location: N. Cali-forn-i-a
Age: 44
Posts: 7,075
Likes: 0
Received 3 Likes
on
3 Posts
Very nice looking ride man ![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
I like those rims. I use to have some Work RS Betas on my old civic and those things were super light. I bet those are really light too![Woot](https://acurazine.com/forums/images/smilies/woot.gif)
If you're planning on getting a bodykit. You should take those mudflaps off ASAP. Mine left light scratches after only 5000 miles.
People say aspec is like 10% stiffer, how much stiffer than stock would say that suspension setup is?
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
I like those rims. I use to have some Work RS Betas on my old civic and those things were super light. I bet those are really light too
![Woot](https://acurazine.com/forums/images/smilies/woot.gif)
If you're planning on getting a bodykit. You should take those mudflaps off ASAP. Mine left light scratches after only 5000 miles.
People say aspec is like 10% stiffer, how much stiffer than stock would say that suspension setup is?
Trending Topics
#10
Moderator
Regional Coordinator (Southeast)
Regional Coordinator (Southeast)
Join Date: Dec 2003
Location: Mooresville, NC
Age: 38
Posts: 43,593
Received 3,791 Likes
on
2,555 Posts
Wow those wheels look amazing on your car. I think you should go with the jdm kit it would look hot on a red car.
#12
Like I said at the meet last week, I really like your wheels. ![Drool](https://acurazine.com/forums/images/smilies/drool.gif)
Nice car!![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
The EuroR kit will look good if you're getting the JDM foglights too. It'll look good too without the JDM foglight, but it would look like it's missing something. Just my
![Drool](https://acurazine.com/forums/images/smilies/drool.gif)
Nice car!
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
The EuroR kit will look good if you're getting the JDM foglights too. It'll look good too without the JDM foglight, but it would look like it's missing something. Just my
![2 Cents](https://acurazine.com/forums/images/smilies/2cents.gif)
#15
Burning Brakes
Thread Starter
Thanks everyone for your kind words!
I'm getting tint as soon as I find the time to drop my car off.
Bodykit wise, I'm leaning towards US OEM kit due to availability and ease of installation (specifically the fog light issue).
But, if anyone knows of a local place in So Cal that can get me the Euro-R kit, I'd really consider going that route. I just don't want to deal w/ a Canadian or out of state vendor in the event that I get damaged parts, etc.
I'm getting tint as soon as I find the time to drop my car off.
Bodykit wise, I'm leaning towards US OEM kit due to availability and ease of installation (specifically the fog light issue).
But, if anyone knows of a local place in So Cal that can get me the Euro-R kit, I'd really consider going that route. I just don't want to deal w/ a Canadian or out of state vendor in the event that I get damaged parts, etc.
#18
Originally Posted by AlterZgo
But, if anyone knows of a local place in So Cal that can get me the Euro-R kit, I'd really consider going that route. I just don't want to deal w/ a Canadian or out of state vendor in the event that I get damaged parts, etc.
These guys are local in the San Gabriel Valley area. I know that they import many JDM engine parts, but I'm sure they can probably import JDM accessories too. Give them a call.
#19
Geaux Tigers!!!
Join Date: Dec 2003
Location: Baton Rouge, LA
Age: 41
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
go with the euro kit, I like it better than the OEM one, plus EVERYONE seems to have the OEM kit.
Also, the jdm headlights would make you car soooo HOTTT!
Amanda
Also, the jdm headlights would make you car soooo HOTTT!
Amanda
#23
WOW man BEAUTIFUL car!!!!! How much did those wheels run you? I was actually looking at a set of those, but now I guess I will have to change........and find something else! Definatly get two thumbs up from me! As far as a choice...the US OEM kit or the Euro kit would look great....
#25
Burning Brakes
Thread Starter
vwong - Thanks for the link. I'll give them a call.
mandercruso - I remember you had a thread about red TSXs w/ the Mugen kit. Do you happen to have any pictures of red Euro-Rs or red TSXs w/ the Euro-R kit?
Ackman - The ride quality is very good. IMO, it's too soft. Comptech 110-155s are probably the softest aftermarket springs available. Their rates are just slightly stiffer than stock. I went w/ this set up b/c I wanted to ensure that I had something with good ride quality. Now, I'm considering going to a stiffer set up like some Tein SS or Flex, but probably not for a while.
JT2k4TSX - Rims and tires cost about $3K. What other rims were you considering? I was thinking about the Volk Progressiv ME or Volk GT-V, but went w/ Work as they are less popular.
Thanks again everyone. Glad you guys (and girl) enjoyed the pictures.
mandercruso - I remember you had a thread about red TSXs w/ the Mugen kit. Do you happen to have any pictures of red Euro-Rs or red TSXs w/ the Euro-R kit?
Ackman - The ride quality is very good. IMO, it's too soft. Comptech 110-155s are probably the softest aftermarket springs available. Their rates are just slightly stiffer than stock. I went w/ this set up b/c I wanted to ensure that I had something with good ride quality. Now, I'm considering going to a stiffer set up like some Tein SS or Flex, but probably not for a while.
JT2k4TSX - Rims and tires cost about $3K. What other rims were you considering? I was thinking about the Volk Progressiv ME or Volk GT-V, but went w/ Work as they are less popular.
Thanks again everyone. Glad you guys (and girl) enjoyed the pictures.
#27
Burning Brakes
Thread Starter
Not yet. But, I have an appt at West End Alignment in Gardena on Thursday and I'll probably swing by Dr. Tint afterwards. The shop I found in the area you mentioned was "A-1 Tint Doctor". I'm assuming this is the correct shop.
#28
Apex Clipper
Join Date: Apr 2005
Location: So-Cal
Age: 45
Posts: 612
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by AlterZgo
Not yet. But, I have an appt at West End Alignment in Gardena on Thursday and I'll probably swing by Dr. Tint afterwards. The shop I found in the area you mentioned was "A-1 Tint Doctor". I'm assuming this is the correct shop.
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
![ugh](https://acurazine.com/forums/images/smilies/ugh.gif)
But the Lumar and other tints are top quality especially their warranty...
#29
Burning Brakes
Thread Starter
Originally Posted by Tsx536
Very nice looking ride man ![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
People say aspec is like 10% stiffer, how much stiffer than stock would say that suspension setup is?
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
People say aspec is like 10% stiffer, how much stiffer than stock would say that suspension setup is?
At approx 315 lb/in F and 170 lb/in rear, the front Comptech 110-155 springs are a little over 10% stiffer in front and the same or very slightly softer in the rear.
Koni shocks have adjustable damping and are also very comfortable. At the softest setting, the car feels too wallowy when going over fwy dips and bumps. At 1 full turn, the wallowy feel is gone but the ride quality is still very good.
Here's a thread by tmalzahn w/ pictures of the tags on the springs showing the actual measured spring rate of Comptech 110-155 springs. See pictures 5-8:
https://acurazine.com/forums/showthr...&threadid=7351
#31
Rep'n Taxbrain.com
Join Date: Aug 2004
Location: N. Cali-forn-i-a
Age: 44
Posts: 7,075
Likes: 0
Received 3 Likes
on
3 Posts
Originally Posted by AlterZgo
People have indicated that stock spring rates are 5 kg/mm F and 3.1 kg/mm R which works out to 280 lb/in F and 173.6 lb/in rear.
At approx 315 lb/in F and 170 lb/in rear, the front Comptech 110-155 springs are a little over 10% stiffer in front and the same or very slightly softer in the rear.
Koni shocks have adjustable damping and are also very comfortable. At the softest setting, the car feels too wallowy when going over fwy dips and bumps. At 1 full turn, the wallowy feel is gone but the ride quality is still very good.
Here's a thread by tmalzahn w/ pictures of the tags on the springs showing the actual measured spring rate of Comptech 110-155 springs. See pictures 5-8:
https://acurazine.com/forums/showthr...&threadid=7351
At approx 315 lb/in F and 170 lb/in rear, the front Comptech 110-155 springs are a little over 10% stiffer in front and the same or very slightly softer in the rear.
Koni shocks have adjustable damping and are also very comfortable. At the softest setting, the car feels too wallowy when going over fwy dips and bumps. At 1 full turn, the wallowy feel is gone but the ride quality is still very good.
Here's a thread by tmalzahn w/ pictures of the tags on the springs showing the actual measured spring rate of Comptech 110-155 springs. See pictures 5-8:
https://acurazine.com/forums/showthr...&threadid=7351
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
Can't decide between your setup, Tein SS, or the Eibach Prosystem.
![Ponder](https://acurazine.com/forums/images/smilies/ponder.gif)
#32
Burning Brakes
Thread Starter
Originally Posted by Tsx536
Great post man. Thanks for the info ![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
Can't decide between your setup, Tein SS, or the Eibach Prosystem.![Ponder](https://acurazine.com/forums/images/smilies/ponder.gif)
![Thumbs Up](https://acurazine.com/forums/images/smilies/thumbsup.gif)
Can't decide between your setup, Tein SS, or the Eibach Prosystem.
![Ponder](https://acurazine.com/forums/images/smilies/ponder.gif)
Eibach Pro-System might be pretty good. Unfortunately, we may never find out as they've been delayed over, and over, and over again for the past 5 mos. Who knows when they'll actually be available?
#36
Great looking car, extra clean. Do you happen to know how much those wheels weigh?
#37
Burning Brakes
Thread Starter
Not sure about the weight. The rim/tire combo felt a little heavier than the stock set up though so I don't think these are light rims like the various Volks.
#39
I spend 2 much time here
Originally Posted by xizor
looks great! your car reminds me of CMF's back in the day, dropped, aftermarket wheels and no body kit, I like it just how it is.
![Werd](https://acurazine.com/forums/images/smilies/werd.gif)