When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
All trunk lips (duck lip both carbon+primed ready to paint and oem type s) will be shipping out next week. This presale price for trunk lips will go up to regular price by end of June! No exceptions (unless you want to put a non refundable deposit down). All new orders may not ship out right away as we have a few extra from this batch, but depending upon how many sell they may go fast, don't worry yours won't take much longer as we will be fully stocked in July!
Carbon front grills we got 10 orders done and shipping out, the rest will be soon to follow and will ship upon order. More to come in toward end of the month and will ship asap.
Actual Trunks are almost done and will be shipping out within a few weeks as well!
I noticed on your site the pre-order price of $245 was effective until August 1st and then the regular price was $385, however the grill is still listed at $245 on your site.
I am definitely interested in the grill in the near future. Need to get some other items sorted on the car before I go back into mods through.
I am trying to install my grill and I am having such a difficult time doing so. One tab on the V-trim does not line up and a few of the others are being S.O.B's! I gave up for now because I don't want to break the trim. As for the hood piece, I am drilling the pilot holes and I am still a bit nervous that I will drill through the CF and or when I hand screw the screws in, the CF will still crack around the screw. As for the center bar, the tabs that I would drill in to are not lined up with the existing holes for the screws. I know that I will be using the tabs that stick out from the bottom of the center bar, but the outer mounting points will not suffice. There has to be better mounting that will provide enough support and make for a better fit.
I so very much want this to work for me but at this point in time, I don't think that it is going to happen.
I am trying to install my grill and I am having such a difficult time doing so. One tab on the V-trim does not line up and a few of the others are being S.O.B's! I gave up for now because I don't want to break the trim. As for the hood piece, I am drilling the pilot holes and I am still a bit nervous that I will drill through the CF and or when I hand screw the screws in, the CF will still crack around the screw. As for the center bar, the tabs that I would drill in to are not lined up with the existing holes for the screws. I know that I will be using the tabs that stick out from the bottom of the center bar, but the outer mounting points will not suffice. There has to be better mounting that will provide enough support and make for a better fit.
I so very much want this to work for me but at this point in time, I don't think that it is going to happen.
All you would have to do for the hood is "mark" with a small hole from the drill or marker / remove and then pre drill in your hand. You can gauge how far to drill based upon screw not having to hold it to the hood to pre drill. The v trim can "bend" a LITTLE but if need be cut off that tab as they're not "all" needed but it is a pain so I understand that but if you push a little in at a time or widen your bumper hole for the v trim it will push right in just fine. So with the v trim you can do one of two things, remove tab or make hole larger on your bumper which I would suggest and it should go right in. The middle bar as instructions is slightly larger mount than the actual holes the mounts would slide in and just need to be widened. The holes I'm talking about that need to be widened are the bumper middle plastic, but most are also just using double sided tape for this as its just as strong. This grill is very light and as long as you pre drill / tighten by hand you can kind of feel or gauge where it needs to stop and if its tight, it should be fine. The only issues I'm running into with customers are shipping as theyre fragile and aftermarket bumpers which aren't "oem spec" and need some trimming to fit.
BOOM. Production started!..... Finally got it down to how I wanted it. We don't just spit parts out, make deadlines, we make the perfect product and deadline follows. The fenders we are fixing one thing to be dead on perfect, hood oem style almost done, vented hood we needed to make sure the oem one fit before making the vented. Patient and time are used in making endless products. PRESALE FOR THE HOOD WILL BE UP SHORTLY!
06-10-2017 | 11:30 AM
