LEDs above exhaust cutout
#1
LEDs above exhaust cutout
Got inspired by the 2016 Accord rear reflectors and found some LEDs and thought I'd give it a try. Wired them to my parking light which the instructions say are 30% brightness and brake light at 100% brightness so they flash brighter when brakes are on. Routed the wires through a hole in the chassis and double sided taped them on--may go back and use screws.
Pretty happy with them. Slightly bigger than I wanted but these were the thinnest profile ones i could find. I could have wired them to signal but then i'd have to wire them independently which meant 1 more solder, or run a relay and have braking and signaling.
Day pictures soon.
Pretty happy with them. Slightly bigger than I wanted but these were the thinnest profile ones i could find. I could have wired them to signal but then i'd have to wire them independently which meant 1 more solder, or run a relay and have braking and signaling.
Day pictures soon.
#6
Senior Moderator
cool!
Trending Topics
#10
Moderator
Join Date: Aug 2014
Location: Dirty H-Town, Amerikkka
Posts: 28,432
Received 7,772 Likes
on
5,045 Posts
Nice! The TSX has some reflectors right about that location (maybe just a little bit higher) and there's a LED retrofit/swap part that some folks have done to give this similar appearance.
I'd also like to see some daytime shots.
I'd also like to see some daytime shots.
#13
Moderator
Join Date: Aug 2014
Location: Dirty H-Town, Amerikkka
Posts: 28,432
Received 7,772 Likes
on
5,045 Posts
For reference, the TSX rear reflectors:
I think you've done a good budget replication!
I think you've done a good budget replication!
The following users liked this post:
wilspainar (08-03-2017)
#17
Pro
I liked it at first but the more I looked at it the more I was like ehhh. I would think the hot exhaust would cause those to not after some time. Way to try something different though!
#18
Honda / Acura Fanboy
Its nice at night and on the first look but if you study it or stare at it itll throw you off a little but overall its a very nice mod just needs a little tweaking and it can be 100%
#21
Where did you get them?
Good job bro! She lookin' sexi over there. Quick question. WheredW you buy them?
Got inspired by the 2016 Accord rear reflectors and found some LEDs and thought I'd give it a try. Wired them to my parking light which the instructions say are 30% brightness and brake light at 100% brightness so they flash brighter when brakes are on. Routed the wires through a hole in the chassis and double sided taped them on--may go back and use screws.
Pretty happy with them. Slightly bigger than I wanted but these were the thinnest profile ones i could find. I could have wired them to signal but then i'd have to wire them independently which meant 1 more solder, or run a relay and have braking and signaling.
Day pictures soon.
Pretty happy with them. Slightly bigger than I wanted but these were the thinnest profile ones i could find. I could have wired them to signal but then i'd have to wire them independently which meant 1 more solder, or run a relay and have braking and signaling.
Day pictures soon.
The following users liked this post:
KC_Chiefs (03-07-2019)
#25
Burning Brakes
Again, that Amazon link is not the exact diffuser OP used. He purchased the following S4Play replica diffuser:
https://www.ebay.com/itm/201504604360
Here is a link to his DIY thread:
https://acurazine.com/forums/3g-tl-p...-946637/page2/
https://www.ebay.com/itm/201504604360
Here is a link to his DIY thread:
https://acurazine.com/forums/3g-tl-p...-946637/page2/
The following users liked this post:
KC_Chiefs (03-07-2019)