AcuraZine - Acura Enthusiast Community - Search Results

Notices
 
Search: Posts Made By: ITL
Showing results 1 to 40 of 478
Search took 0.32 seconds.
01-03-2011, 10:52 AM
Replies: 292
Views: 77,982
Posted By ITL

it drives very good but the mounts are very...

it drives very good but the mounts are very rigid. I definitely would not go for more than 62A. but I also have a car with 115 k and a clutch that needs to be replaced, so there are definitely a few...
12-29-2010, 06:31 PM
Replies: 24
Views: 18,277
Posted By ITL

okay. I just wanted to make sure is wasn't going...

okay. I just wanted to make sure is wasn't going to bork anything ECU related. thx.


As well, just for purposes of documentation, the two top bolts for the side XLR8 mount were 1 1/4" too long,...
12-29-2010, 06:21 PM
Replies: 292
Views: 77,982
Posted By ITL

I just installed the damper along with the XLR8...

I just installed the damper along with the XLR8 engine mounts. The damper was very simple to install, and fit perfectly the first time I put it on.
12-29-2010, 05:58 PM
Replies: 24
Views: 18,277
Posted By ITL

Thanks for the help. I pulled the lines out...

Thanks for the help.

I pulled the lines out and capped off the manifold. I noticed there's a small module to the left of where that vacuum line hooked up. The module is on the vacuum line between...
12-28-2010, 06:14 PM
Replies: 24
Views: 18,277
Posted By ITL

Vacuum lines on engine mounts?

The front mount has a vacuum line running to the bottom of it. I've replaced my engine mounts with the XLR8 mounts, but have no idea what to do with the vacuum lines... I can't just leave them open,...
12-24-2010, 01:33 PM
Replies: 10
Views: 5,582
Posted By ITL

i couldn't get anything wedged into the flywheel,...

i couldn't get anything wedged into the flywheel, nothing wanted to stay in there.

Impact gun wouldn't get it off.

I finally ended up putting a torch on the bolt, wedging a breaker bar on the...
12-20-2010, 07:39 AM
Replies: 44
Views: 2,315
Posted By ITL

Man, you installed your steering wheel, but...

Man, you installed your steering wheel, but listen to your mp3s through a cassette adapter??? :tomato:
12-20-2010, 07:26 AM
Replies: 10
Views: 5,582
Posted By ITL

There are plenty above removing the stock pulley....

There are plenty above removing the stock pulley. I have not been able to find a single thread specific to removing the UR pulley.
12-19-2010, 11:54 PM
Replies: 10
Views: 5,582
Posted By ITL

How to remove UR crank pulley?

So I'm in a bind. I've got everything I need to change my timing belt, but cannot get this crank pulley off. I have the UR pulley, so the Honda tool won't work to hold the crank. Any idea how to get...
12-19-2010, 11:51 PM
Replies: 25
Views: 10,132
Posted By ITL

argh...so I'm in a bind. I've got everything I...

argh...so I'm in a bind. I've got everything I need to do my timing belt, but cannot get this crank pulley off. I have the UR pulley, so the Honda tool won't work. Any idea how to get it off? I can't...
04-20-2009, 08:15 PM
Replies: 1
Views: 797
Posted By ITL

Sold!!!

Sold!!!
04-19-2009, 08:25 PM
Replies: 1
Views: 797
Posted By ITL

FS: 3G Comptech sport springs for TL - $140 in Atlanta

My Comptech springs have just been sitting in a box for a while and it's time to clean up. They are used with 25K miles on them. These springs rode great, but I wanted an extreme drop so I went with...
Replies: 87
Views: 26,479
Posted By ITL

sure, man. I'll PM you my email.

sure, man. I'll PM you my email.
07-14-2008, 10:16 AM
Replies: 7
Views: 2,238
Posted By ITL

I took my car to the dealer a few days ago for...

I took my car to the dealer a few days ago for the power steering and wiper motor recalls, and asked them to take a look at this. It turns out my surging issue is due to a bad accelerator position...
06-27-2008, 12:15 PM
Replies: 7
Views: 2,238
Posted By ITL

so your problem with surging was an overfill of...

so your problem with surging was an overfill of the engine oil? I've had a very small surging issue for the last month or so. It feels like some sort of parasitic drag maybe every 20 seconds or so at...
06-23-2008, 12:20 PM
Replies: 10
Views: 1,194
Posted By ITL

Good to hear. Glad it's an easy fix. Too bad they...

Good to hear. Glad it's an easy fix. Too bad they didn't have any in stock...
06-10-2008, 09:45 AM
Replies: 10
Views: 1,194
Posted By ITL

I'm guessing you have a speed sensor for one of...

I'm guessing you have a speed sensor for one of the wheels that has gone bad. This happened to me before several years ago, and Acura replaced it under warranty.
Replies: 45
Views: 16,546
Posted By ITL

did you ever find any extra connectors?

did you ever find any extra connectors?
Replies: 45
Views: 16,546
Posted By ITL

It wouldn't be possible with just one...

It wouldn't be possible with just one connector...you'd need a connector for the other end of the extension cable. Even if you had both, there are still the other harnesses in the car. I doubt you...
Replies: 45
Views: 16,546
Posted By ITL

IMHO, the glovebox is the most elegant location...

IMHO, the glovebox is the most elegant location for the carpc. Less wiring makes for less potential interference/noise. I didn't use my glovebox for anything anyway...though with my latest case, I...
Replies: 45
Views: 16,546
Posted By ITL

hey nitro, where are you located? Would you be...

hey nitro, where are you located? Would you be willing to drive to Atlanta?

There's nothing very difficult about extending the harnesses, it's just terribly time consuming. I've done this twice,...
Replies: 45
Views: 16,546
Posted By ITL

your install looks very familiar ;) awesome...

your install looks very familiar ;) awesome setup, man!
Replies: 227
Views: 82,788
Posted By ITL

Have fun with it! One thing I regret is not...

Have fun with it! One thing I regret is not taking more pictures behind the dash. My wiring looked better than the factory wiring by the time I got done with it, but no one can see it!

Take lots...
Replies: 227
Views: 82,788
Posted By ITL

to answer your question, the trim pieces running...

to answer your question, the trim pieces running down the sides of the console are the first pieces to come off. They're easy to get out if you know what you are doing, otherwise, they're not real...
Replies: 30
Views: 1,033
Posted By ITL

It's been my experience that the majority of the...

It's been my experience that the majority of the time, you get what you pay for...there's probably a reason $90 is the cheapest.
Replies: 227
Views: 82,788
Posted By ITL

Let us know what state you live in, and we'll be...

Let us know what state you live in, and we'll be able to better help you find someone.
Replies: 99
Views: 10,354
Posted By ITL

dolt +1

dolt +1
Replies: 99
Views: 10,354
Posted By ITL

+2

+2
Replies: 30
Views: 1,033
Posted By ITL

If dan.....k is recommending a shop, I'd...

If dan.....k is recommending a shop, I'd definitely trust it. He's had a LOT of work done around town and won't settle for anything less than the best.

dan....k and alpha, thanks for the good...
Replies: 170
Views: 12,852
Posted By ITL

Hey Matt, I believe you have to have 4-5 posts...

Hey Matt,
I believe you have to have 4-5 posts on the forums before you can PM other members. I'll send you an email to your comacst account :)
11-17-2007, 12:32 AM
Replies: 11
Views: 1,086
Posted By ITL

yes. auto drivetrain assumes more power loss than...

yes. auto drivetrain assumes more power loss than manual tranny. I believe it's due to the torque converter in the auto.
Replies: 170
Views: 12,852
Posted By ITL

i have used a high pressure sprayer (coin-op car...

i have used a high pressure sprayer (coin-op car wash) directly at the camera numerous times without any issue. I've never had condensation problems after using my hose at home or the high pressure...
Replies: 6
Views: 997
Posted By ITL

There are several members of this forum,...

There are several members of this forum, including myself, that have built carPCs in several 3G TLs. All you have to do is ask around :thumbsup:

As far as this being a better PC than the carPCs...
Replies: 170
Views: 12,852
Posted By ITL

I hooked up both cameras to my car, and decided...

I hooked up both cameras to my car, and decided hands down to go with the 44R. The 24R didn't give me enough coverage. I posted a comparison, check out post #83 of this thread (page 4, I think).
Replies: 6
Views: 997
Posted By ITL

many of us have built full purpose carpcs the...

many of us have built full purpose carpcs the size of the pc in your thread, that are much more powerful.
10-30-2007, 03:49 PM
Replies: 205
Views: 7,414
Posted By ITL

what's going on?

what's going on?
10-16-2007, 08:54 AM
Replies: 205
Views: 7,414
Posted By ITL

n e word, yet?

n e word, yet?
Replies: 87
Views: 26,479
Posted By ITL

screamin, here you go: PSU: M2-ATX. Bootup...

screamin, here you go:
PSU: M2-ATX. Bootup takes about 30 seconds, which is pretty good for my setup.
OS: Windows XP SP2 (would prefer Linux, but there's a lack of good navi sw)
PSU has a...
Replies: 87
Views: 26,479
Posted By ITL

My current carpc is a 1.7GHz Pentium M with 1GB...

My current carpc is a 1.7GHz Pentium M with 1GB of ram. It actually stays pretty cool, now that I have really good airflow in the glovebox. It has never overheated, unlike my very first couple of...
08-28-2007, 08:56 PM
Replies: 315
Views: 110,113
Posted By ITL

enjoying the updates....keep em coming!

enjoying the updates....keep em coming!
Showing results 1 to 40 of 478
 


 
Forum Jump

Contact Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.