The Manthey Racing team from Germany will run two brand new Porsche 911 GT3 RSR race cars in the 24 hour race at Spa in Belgium on 29 July. Porsche developed the near-standard racing sportscar based on the recently-introduced 911 GT3 RS road car, and put it in the hands of the experienced team under the direction of team principal Olaf Manthey. Works drivers Timo Bernhard and Marc Lieb (both from Germany) share driving duties with Pedro Lamy from Portugal in the GT3 RSR with starting number '111'. Driving the Porsche with starting number '197' are further 'works' drivers Lucas Luhr (Monaco), Sascha Maassen (Belgium) with Marcel Tiemann (Monaco).

Based on the current 911 GT3 RS, a particularly light and sporty derivative of the 911 GT3, the new GT3 RSR is designed to comply with the A.C.O (Automobile Club de lOuest), the FIA-GT and IMSA (International Motorsports Association) as well as VLN (Veedol Langstrecke Nuerburgring) regulations. Porsche decided to build the new GT3 RSR after analysing the A.C.O. and FIA regulations in a specification which allows a minimum weight of 1,225 kilograms (predecessor: 1,125 kgs) and permits the tyre width to be increased by two inches to now 14 inches. 35 kilograms of the required additional weight may be placed as ballast in the vehicle, contributing to a lower centre of gravity.

For the normally-aspirated Porsche engine this specification allows a capacity of 3.8-litres with two 30.3 millimetre air restrictors (predecessor: 3.6-litres, two restrictors with 29 mm diameter). The increase in displacement was achieved through the enlargement of the bore to 102.7 millimetres with the unchanged stroke of 76.4 mm. With the mandatory air restrictors, the unit delivers 359 kW/485 hp at 8,500 revs per minute. Maximum torque increased to 435 Nm. Top engine speed is reached at 9,000 rpm. Thanks to the increase in capacity and the corresponding reprogramming of the electronics the top performance as well as the response and driveability have further improved. The efficiency of the mid-front radiator was increased while the radiators flanking the centre unit on each side are the same as in the high performance Carrera GT.

The latest GT3 RSR features the proven sequential six-speed gearbox with ignition cut of its forerunner.

The bodyshell of the GT3 RSR with the welded-in safety cage is ten percent stiffer than its predecessor. Distinctive wheel arches widen the body by 50 millimetres on each side. The track is enlarged correspondingly; wheels and tyres of the maximum allowable dimension can be fitted.

The relocation of the supplementary oil tank (option), the power steering and the battery to the front improve the weight distribution. The front and rear lids, the front mudguards, the wider rear, the doors as well as the front and rear panelling and wing consist of carbon-fibre composite material. The rear and side windows are manufactured from light polycarbonate.

The newly-developed aerodynamic package improves the aerodynamic efficiency compared to the forerunner (type 996 GT3 RSR) by around seven percent. Airflow to and from the radiators, the brakes and the engine were further optimised. In compliance with the FIA and A.C.O. regulations the new GT3 RSR features a flat underbody.

The suspension with Porsche-optimised struts at the front and the Porsche multi-link axle at the rear corresponds to the configuration of the standard car. The modified kinematics are set-up for the wider tyre footprint and for the lowest possible camber change in rebound and compression. The new ZFSachs shock absorbers feature the Through-Rod-System with considerably lower chamber pressure and hence less friction than conventional dampers. As a result they offer a significantly improved response characteristic. The position of the rear axle was optimised. The axle features a new anti-rollbar, an adjustable upper link and an optimised lower link.

The brake system features six-piston aluminium callipers and 35 millimetre thick brake discs measuring 380 mm in diameter at the front and 30 millimetre four-piston aluminium callipers with 355 mm diameter discs at the rear.

Over the 2006/07 winter, 35 units of the new racing sportscar will initially be built.

Porsche is the biggest name in endurance sportscar racing worldwide, and its racing engineers plan on keeping it that way. Following the introduction of the GT3 Cup S comes a new-and-improved version of its big brother, the GT3 RSR. The most powerful 911-based racer Porsche makes, the RSR produces 465 horsepower from its 3.8-liter flat-six, and revs all the way to a 9400rpm redline. Although the engine carries over unchanged from the previous version, improvements have been made to the aerodynamics, suspension and transmission. Most visible is the new front end, with additional "flick" spoilers, enhanced air intakes and aerodynamically-optimized air outlets. The suspension offers a wider range of adjustability, and the RSR now features the six-speed sequential gearbox from the even-badder RS Spyder sports-prototype.

Despite its alphanumeric designation, the GT3 RSR actually competes in the GT2 class, where it will face stiff competition from the likes of the Corvette C6R, Ferrari F430 GT2 and the upcoming Aston Martin Vantage GT2.
Thirty-five orders for the new GT3 RSR have already been placed, at nearly €350,000 apiece, and are being filled by Porsche's Weissach workshop.

The Porsche GT3 RSR launches into the new model year with extensive modifications. The most powerful race car based on the Porsche 911, which last year scored wins at the 24 hour races of Le Mans and Spa as well as overall victory at the Nuerburgring 24 hours, competes in the GT2 class at international long distance races. The most distinguishing feature of the new GT3 RSR is the front end which received major improvements to the aerodynamics. The majority of innovations however are hidden under the weight-optimised body.

Aside from the easily recognisable additional spoilers on the front apron, so-called flicks, an optimised air ducting with newly-designed side air outlets generates more downforce and reduces drag. The rear end including the rear wing was taken over from the predecessor. Extensive changes to the suspension cinematics increase mechanical grip considerably. The range of possible suspension set-ups was broadened.

The 3.8-litre boxer engine of the GT3 RSR remains unchanged apart from slight improvements to details. It delivers 465 hp (342 kW) at 8,000 revs per minute and delivers a maximum torque of 430 Nm at 7,250 revs. The rev limiter of the efficient six-cylinder kicks in at 9,400 rpm.

Much of the know-how in the GT3 RSR's totally new gearbox has come from the RS Spyder sports prototype. The sequential six-speed unit, developed by Porsche engineers, is considerably lighter than its predecessor. Internal friction was substantially reduced. The flat angle of the drive shafts allows teams a wider range of suspension set-ups.

Aside from the GT3 Cup and the GT3 Cup S, the GT3 RSR is the third race car based on the Porsche 911 offered by Porsche Motorsport. Thirty-five units of the fastest and most powerful long distance racer made in Weissach, apart from the exclusive RS Spyder sports prototype, are now being produced and delivered to customer teams around the globe. The price of the GT3 RSR is 349,800 Euro plus VAT.


Technical Description Porsche GT3 RSR (2008)

Engine

Six-cylinder aluminium boxer engine, water-cooled; 3,795 cc; stroke 76.4 mm; bore 102.7 mm; 465 bhp (342 kW) at 8,000 rpm; max. torque 430 Nm at 7,250 rpm; air restrictors 2 x 29.5 mm; maximum engine speed 9,400 rpm; four valves per cylinder; dry sump lubrication; individual throttle butterflies; central air intake; electronic MS 4.0 engine management;
fuel injection; fuel grade: RON 98 Super Plus unleaded.

Power transmission

Six-speed gearbox with sequential jaw-type shift; oil/water heat exchanger; single-mass flywheel; hydraulic disengagement lever; three-plate carbon-fibre clutch; rear wheel drive; limited-slip differential 45/65 %.

Body

Monocoque body (basis GT3 RS) of hot-galvanised steel; aerodynamically optimised front end with front spoiler; aerodynamically optimised front underfloor; adjustable rear wing; 90-litre safety fuel tank with fast filling function; air jack; welded-in safety cage; bucket-type racing seat (on driver's side only) with flame-resistant seat cover; six-point seat belt adapted for use of the HANS Head and Neck Support; electric fire-extinguishing system.

Suspension

Front: McPherson spring strut axle; Sachs four-way gas pressure dampers; double coil springs (main and ancillary spring); front axle arms adjustable for camber; adjustable sword-type anti-roll bar on both sides; power steering.
Rear: Multi-arm axle with rigidly mounted axle sub-frame; Sachs four-way gas pressure dampers; double coil springs (main and auxiliary spring); rear axle tie-bar reinforced and infinitely adjustable; adjustable sword-type anti-roll bar on both sides.
Complete suspension infinitely adjustable (height, camber, track).

Brakes

Brake system with balance bar control.
Front: Single-piece six-piston aluminium fixed callipers; inner-vented, 380 mm in diameter; racing brake pads.
Rear: Single-piece four-piston aluminium fixed callipers; inner-vented, 355 mm in diameter; racing brake pads.

Wheels

Front: Three-piece BBS light-alloy wheels (11J x 18-34); central bolt;
Rear: Three-piece BBS light-alloy wheels (13J x 18-12.5); central bolt.

Electrical System

Motec display with integrated data recording; adjustable traction control; battery: 12 volt, 50 Ah, 140 Ah alternator.

Weight

Approx. 1,225 kg complying with A.C.O. regulations, 1,200 kg complying with FIA regulations.

The successful Porsche 911 GT3 RSR takes off into the new model year with extensive modifications. The most powerful race car based on the Porsche 911, which last season secured wins in the American Le Mans Series and at the Nürburgring 24 Hours, competes in the GT2 class at international long distance races. The most distinguishing feature of the new GT3 RSR is the redesigned front with large air outlets on the front hood. Under the light-weight bodyshell, as well, major changes were made to the quickest 911.

Noticeable at first sight are the air outlet slots, or the so-called louvers, on the front hood: an indication of the completely redesigned air ducting of the radiators, which became necessary through the new design of supply and discharge air with the installation of an optional air-conditioning unit. The aerodynamics under the rear underwent further optimisation. The rear wing now features a wider adjustment range. The weight-optimised brake system and the lighter wiring harness contribute to further improved handling, compared to the predecessor model.

The capacity of the well-known six-cylinder boxer engine increased from 3.8 to 4.0-litres. After another reduction in the size of the air restrictors for the 2009 season, the engine now delivers around 450 hp (331 kW) at 7,800 revs per minute and develops a maximum torque of 430 Nm at 7,250 rpm. The rev limiter of the efficient six-cylinder unit kicks in at 9,000 rpm. Compared to the forerunner, the rev level for a given power output was significantly lowered. Thanks to this, the engine features an optimised torque curve and offers better driveability.

In the cockpit, a new multi-function display located above the dashboard indicates the opti-mum moment to change gears. Another new feature is the programmable multi-function, onboard supply system control device, giving teams the choice of many individual functions. One of these is the infinitely adjustable blinking frequency of the lights in the front apron, which helps to immediately recognise race cars when they enter the pits in the dark. For eas-ier servicing under race conditions, other modifications were made. The GT3 RSR now fea-tures a new air-jack system with overpressure valve. The oil refill with fast filling function has now moved to the rear lid, giving mechanics better access.

Aside from GT3 Cup and the GT3 Cup S, the GT3 RSR is the third race car based on the Porsche 911 offered by Porsche Motorsport. About 20 of the successful long distance racers have been built in Weissach and are now being delivered to customer teams around the world. The GT3 RSR costs 380,000 Euro plus VAT specific to each country.

The Porsche 911 GT3 RSR takes off into the new motorsport season with extensive modifications. The 2011 version of the world’s most successful GT race car celebrated its international premiere at the “Night of Champions” party held at the R&D Centre in Weissach to mark the end of the motorsport season. Priority in the further development of the GT3 RSR was given to the newly designed aerodynamics at the front and rear, changes to the suspension kinematics and to the engine.

The 4.0-litre, six-cylinder boxer engine now delivers 455 hp (335 kW) at 7,800 revs, five horsepower more than its predecessor. The power increase results from an engine management system which adapts even better to different fuel grades, as well as a redesigned exhaust system and a modified air intake housing. Moreover, the driveability of the famously efficient engine has undergone further improvements. Maximum revs remain unchanged at 9,400 rpm.

Clearly visible are the modifications to the front. A new front lip provides higher downforce at the front axle. The front wheels are now wider with the rims growing from 11 to 12 inches giving additional grip and less of an understeering tendency. The position of the rear wing and the shape of the wing mounting also underwent optimisation and were adapted to the new rear fairing with additional air outlet louvers. The rear lid was also redesigned for optimised air ducting. Like the 911 GT3 Cup and the GT3 R, the RSR has now been equipped with the LED rear lights taken from the latest 911 road-legal cars.

The 911 GT3 RSR joins the 911 GT3 R and the 911 GT3 Cup as the top model of Porsche Motorsport’s product range. The successful long distance racer from Weissach can be ordered now at a price of 410,000 Euro plus country-specific value added tax. All 2011 modifications are available as a kit for GT3 RSR cars from the 2010 season.

Technical description Porsche GT3 RSR (2011 model year)

Engine
Water-cooled six-cylinder boxer engine; 3,996 cc; stroke 80.4 mm; bore 102.7 mm; 455 hp (335 kW) at 7,800 rpm; max. torque 450 Nm; air restrictors 2 x 28.6 mm; max. revs 9,400 rpm; four valve technology; dry sump lubrication; individual throttle butterflies; fuel injection.

Transmission
Porsche six-speed gearbox with sequential jaw-type shift; oil/water heat exchanger, single-mass flywheel; hydraulic disengagement lever; three-plate carbon-fibre clutch; rear wheel drive; limited slip differential 45/65 percent.

Body
Monocoque body (basis GT3 RS) of hot-galvanised steel; aerodynamically optimised front end with front spoiler; aerodynamically optimised front underfloor; adjustable rear wing; 90-litre FT3 safety fuel tank with fast filling function; air jack; welded-in safety cage; race seat (driver’s side only) with flame retardant upholstery; six-point seat belt adapted for use of the HANS Head and Neck Support; electric fire extinguishing system.

Suspension
Front axle: McPherson spring strut axle; Sachs four-way gas pressure dampers; double coil springs (main and auxiliary); front axle arms adjustable for camber; adjustable sword-type anti-roll bar; power steering.
Rear: Multi-arm axle with rigidly mounted axle sub-frame; Sachs four-way gas pressure dampers; double coil springs (main and auxiliary); rear axle tie-bar reinforced and infinitely adjustable; adjustable sword-type anti-roll bar. Complete suspension infinitely adjustable (height, camber, track).

Brake system
Brake system with balance bar control.
Front: Single-piece six-piston aluminium fixed callipers; inner vented, 380 mm diameter; racing brake pads.
Rear: Single-piece four-piston aluminium fixed callipers; inner vented, 355 mm diameter; racing brake pads.

Wheels
Front: Three-piece BBS light-alloy wheels (12J x 18 ET 34); central bolt.
Rear: Three-piece BBS light-alloy wheels (13J x 18 ET 12.5); central bolt.

Electrical system
Motec display with integrated data recording; multi-function display with integrated gearshift indicator; adjustable traction control; battery: 12 volt, 80 Ah, 140 Ah alternator.

Weight
1,220 kg