Twin Cities Acuras
#6161
Haha....very funny You're probably right, but I have a feeling I know what it is, but just don't want to deal with it
Hmm....if you're bored after the tune feel free to swing by my place as I'll probably be under the car working on the rsb
#6162
Punctuation Nazi
Well I got in a little fender bnder the other day. luckily the new bumper wasn't on yet. but I am working on it. anyways, it will take a little bit to get this up to 100%...
oh, the "surprise" was a JDM bumper.. It's at my buddies shop right now, I just finished sanding it down, but i got the foglights here at my house
oh, the "surprise" was a JDM bumper.. It's at my buddies shop right now, I just finished sanding it down, but i got the foglights here at my house
#6165
fu
Join Date: May 2008
Location: Woodbury, MN
Age: 33
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
1
and just fyi 2 is a bitch.. trust me as someone who has gone down that path twice with poor results... the cheap accord kits on ebay the lens will shatter within a month.. mine made it 15 mins in the cold on the 2 set. unless you are really good at what it takes to do it (I am not, just figured it was worth a shot, now I have a cut-up ugly front bumper), stay clear
and just fyi 2 is a bitch.. trust me as someone who has gone down that path twice with poor results... the cheap accord kits on ebay the lens will shatter within a month.. mine made it 15 mins in the cold on the 2 set. unless you are really good at what it takes to do it (I am not, just figured it was worth a shot, now I have a cut-up ugly front bumper), stay clear
#6167
Well about 37 new cuts later and I got the endlinks and RSB on my TL! Just a warning to anyone planning on replacing their endlinks.....have a good grinder handy!! Damn bolts stripped, so off with their heads!! Haha But after a couple cloverleaves I totally recommend replacing the RSB. I have virtually no understeer now!! Oddly enough my front passenger tire is what was squealing as I went around the curves.....I'll have to look into it.
Hmm....now what to do.....still time for a couple mods before winter
Hmm....now what to do.....still time for a couple mods before winter
#6168
Punctuation Nazi
Other than that, the change to the geometry caused by the stiffer RSB may have started to lift that tire under extreme cornering. I have seen BMWs lift the inside front tire 4-6 inches on hard cornering.
#6169
Check tire pressures, you might have been rolling the tire and squealing it on the sidewall, that part doesn't offer nearly as much grip.
Other than that, the change to the geometry caused by the stiffer RSB may have started to lift that tire under extreme cornering. I have seen BMWs lift the inside front tire 4-6 inches on hard cornering.
Other than that, the change to the geometry caused by the stiffer RSB may have started to lift that tire under extreme cornering. I have seen BMWs lift the inside front tire 4-6 inches on hard cornering.
That's kinda scary.....4-6 inches?! Don't get me wrong, it still held the corner just fine, but weird that the front inside tire is what was squealing. I don't typically take corners that hard, so I'll start with the tire pressure and go from there. Thanks Josh.
#6170
Punctuation Nazi
Yeah, Darryl Wrolson runs his 328 in STX and his car is fully prepped. I have seen his car lift the inside that high when either he or one of the other really fast drivers get behind the wheel. He is also the guy that smoked my all last season.
There is another guy that runs in the local series that almost rolled his car in the dry, flat, concrete because he had so much grip. There is a picture of it somewhere, if I find it I'll post it up here.
There is another guy that runs in the local series that almost rolled his car in the dry, flat, concrete because he had so much grip. There is a picture of it somewhere, if I find it I'll post it up here.
#6172
#6173
Don't feed the...WTF?
I think this winter is going to be my car year. I'm at 77k now. Think I'm going to do the plugs, all fluids, maybe take a crack at the cabin filter, and possibly a brake job (slotted rotors and all, depending on how much cash I've got at the time I do it)
#6174
Broke college grad
Join Date: May 2007
Location: Blaine, Minnesota
Age: 34
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, Darryl Wrolson runs his 328 in STX and his car is fully prepped. I have seen his car lift the inside that high when either he or one of the other really fast drivers get behind the wheel. He is also the guy that smoked my all last season.
There is another guy that runs in the local series that almost rolled his car in the dry, flat, concrete because he had so much grip. There is a picture of it somewhere, if I find it I'll post it up here.
There is another guy that runs in the local series that almost rolled his car in the dry, flat, concrete because he had so much grip. There is a picture of it somewhere, if I find it I'll post it up here.
#6176
What's the name of this place? I'm looking for a set of replacement headlights to take apart and clear this winter. Easier to mess with stuff when you have backups of them I might want to go check it out if you're pulling parts off an 04 TL!
#6177
Broke college grad
Join Date: May 2007
Location: Blaine, Minnesota
Age: 34
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
#6178
I thought you were selling your car?! What happened with that??? I've been patiently waiting for those headlights I take it you have a heated garage to work in or are you having someone do the work?
#6181
Broke college grad
Join Date: May 2007
Location: Blaine, Minnesota
Age: 34
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
#6182
T-Swzy
Thread Starter
Join Date: Jun 2007
Location: Saint Paul, MN
Age: 36
Posts: 2,575
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ts_vaj
If any of you 2G fellas are looking for some junk parts for your cars, I found this autobody shop down in the Bloomington area near Mall of America who seems to pick up alot of junk TLs.
If any of you 2G fellas are looking for some junk parts for your cars, I found this autobody shop down in the Bloomington area near Mall of America who seems to pick up alot of junk TLs.
#6184
So were is this place? Need an address or name of the place I want to get there before 05 tl rider.
#6185
Hey glow dod you still have your old HID projector lenses.
#6186
#6187
The iridium plugs that XLR8 sells for apparently $11 each
I think my game plan is to buy the innovative motor mounts, RV-6 precat deletes, RV-6 resonated test pipe, and NGK plugs and do it all at once, cause the front strut bar has to be removed to do them all except the test pipe. Makes sense to take it apart one time to get it all taken care of. I'm gonna have a busy spring
#6188
Don't feed the...WTF?
Why yes.. I do actually. I've got the lenses and the old housings for them as well. You thinking of doing a headlight project and want to make a complete set without taking yours apart? Or you thinking projector fogs?
Either way - I'm not doing anything with them so if you want them, their yours.
Either way - I'm not doing anything with them so if you want them, their yours.
#6189
Why yes.. I do actually. I've got the lenses and the old housings for them as well. You thinking of doing a headlight project and want to make a complete set without taking yours apart? Or you thinking projector fogs?
Either way - I'm not doing anything with them so if you want them, their yours.
Either way - I'm not doing anything with them so if you want them, their yours.
How much you want for them?!
#6191
Don't feed the...WTF?
It's kind of still for sale. If someone wanted to buy it, it's for sale. But I'm done advertising it - so for all practical purposes I've decided to keep it.
Although if I did ever decide to sell it, I would just end up buying some impractical 2 seater or convertable since it doesn't have to be my daily driver anymore.
As for the lenses, I never really thought about it. In my eyes, they are nothing special - just lenses. Heck - come and get them and I'd give them to ya. If I had to deliver, I'd probably want some beer or something. lol
But.. you all do have me wondering why all of the sudden everyone wants my lenses. I'm going to give them away to someone, and they are going to do something really cool with them. Then I'm gonna have to steal them back
Although if I did ever decide to sell it, I would just end up buying some impractical 2 seater or convertable since it doesn't have to be my daily driver anymore.
As for the lenses, I never really thought about it. In my eyes, they are nothing special - just lenses. Heck - come and get them and I'd give them to ya. If I had to deliver, I'd probably want some beer or something. lol
But.. you all do have me wondering why all of the sudden everyone wants my lenses. I'm going to give them away to someone, and they are going to do something really cool with them. Then I'm gonna have to steal them back
#6192
Punctuation Nazi
#6194
Broke college grad
Join Date: May 2007
Location: Blaine, Minnesota
Age: 34
Posts: 602
Likes: 0
Received 0 Likes
on
0 Posts
haha I'm just kidding I just saw her drive by was all, subi is looking mighty fine with winter beaters on
#6195
Hey Glo, I'll come pick up the lenses this weekend.
Can you find out what RAM I need for my computer?
I have an AMD 64 X2 4000+ 2.1GHz sold by HP, model a1737c and I only have 1GB of RAM so it's slow as shit. I want to max this bitch out.
Can you find out what RAM I need for my computer?
I have an AMD 64 X2 4000+ 2.1GHz sold by HP, model a1737c and I only have 1GB of RAM so it's slow as shit. I want to max this bitch out.
#6197
Don't feed the...WTF?
http://www.newegg.com/Product/Produc...82E16820231136
(Or you can just buy 3 individual sticks, but the cost savings will pretty much be none, so you might as well get all 4 matching)
#6198
Selling my wheels. Lowered price, $1200!!, let me know if any of you guys are interested.
https://acurazine.com/forums/car-parts-sale-361/fs-19x8-ssr-sovereign-wheels-368970/
https://acurazine.com/forums/car-parts-sale-361/fs-19x8-ssr-sovereign-wheels-368970/
#6199
Wow, so I finally did some testing with the water/meth kit today... The ambient temperature at the time of testing was 61 F.
IAT before water/meth: 133 F
IAT after water/meth: 68 F
The temp would typically drop about 5+ degrees/second until it reached its low-point.
Final thoughts: Holy crap. I'm blown away by how effective that is. As far as I'm concerned, for $400 that's a MUST HAVE for any F/I cars.
IAT before water/meth: 133 F
IAT after water/meth: 68 F
The temp would typically drop about 5+ degrees/second until it reached its low-point.
Final thoughts: Holy crap. I'm blown away by how effective that is. As far as I'm concerned, for $400 that's a MUST HAVE for any F/I cars.
#6200
Punctuation Nazi
Hey Glow, we were finally able to get it to work. Had to remove the card, remove the software, and install the newest software, then the card. Then put one stick in at a time and it now works, he has 4GB RAM! This machine is transformed!