AcraAdi93

Category: Drivetrain
Price: $1500
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): CL 2G, TL 2G
Location (State/Prov/Terr): IL
Item Condition: Brand New

Engine. J32A2 If needing a new engine look for a CLs-6 motor (if not see below *)
03 CLs-6 speed manual.
03 CLs-6 Manual Engine Harness. 32110-PGE-A11
03 CLs 6 speed ECU
03 CLs-6 Flywheel 22100-PGE-026
03 CLs-6 Flywheel bolts (Qty 8) 90011-PGE-000 (CHECK)
03 CLs-6 Clutch Assembly 22105-PGE-305 (unfortunately right now there arent many options for aftermarket clutches)
03 CLs-6 Rear Engine mount and bracket 50810-S3M-A01, 50827-S3M-A00, BOLT (m12X25) 90166-S3M-A00
03 CLs-6 Rear and Front Engine Dampener and bracket (i would recommend aftermarket here)
03 CLs-6 Shifter and cables. 54100-S3M-A01, 54310-S3M-A01 (check)
03 CLs-6 Starter 31200-PGE-A11 (try to locate used, its expensive) (check)
03 CLs-6 Gauges (CHECK)
03 CLs-6 Hydraulic Clutch lines. 46960-S3M-A01, & 46970-S3M-A01 (CHECK)
03 CLs-6 Trans mounts (2 of them) 50806-S3M-A03, 50805-S3M-A03
03 CLs-6 Cup Holder 77230-S3M-A01ZA (CHECK)
03 CLs-6 Parking brake 47105-S3M-A04ZA and to go with it,
Spring 47537-671-670, Nut 47522-594-000, Equalizer pin 47365-538-000, Equalizer 47360-SB2-000 (CHECK)


*If you use the J32A2 from the Auto you will need these parts (all from the CLs-6)

Front cam pulley 14260-PGE-A11
Front plate assembly (behind cam pulley) 11860-PGE-A10 (CHECK)
Timing belt pulley(lower) 13621-PGE-A11
Crank shaft sensor 37500-PGE-A11 (CHECK)
Subharness for CKP 37501-PGE-A10
TDC Sensors (Qty 2) 37840-PGE-A11
TDC SUB HARNESS 37841-PGE-A10 (CHECK)



If you dont already have the Type-s you will want the IMRC 37850-PGE-A01

Brake/Gas pedal assembly from either the accord or CLs-6. (i modified mine)
If you decide to buy it new BRAKE PEDAL ASSY 46600-S3M-A51 (CHECK)

Clutch pedal. (this can be from a few cars, i took mine from a 90s civic. it was almost a direct bolt in.
It uses 3 points to bolt in only 2 lined up. I modified a bolt and shim to make it bolt up in the 3rd spot) (check)

If you decide to buy it new you will need the pedal and mount CLUTCH PEDAL 46910-S3M-A01 & CLUTCH PEDAL BRACKET 46990-S84-A01 (check)
MASTER CYLINDER ASSY 46922-S3M-A01 & Clutch Fluid Tank 46965-S5A-013, & Clutch Hose 46961-S3M-A02
(i used the one from the civic i pulled the clutch pedal out of)

Things im not sure if you will need but i bought.

Relay box assembly (under hood) 38250-S3M-A22
Shift Boot 83414-S3M-A01ZA (check)
Shift Knob 54102-SL0-023ZB (check)

If you have a header you will either have to have the XS header or Comptech header for the manual. Other wise it wont fit
You will be able to reuse the stock manifolds

If you already have a Type-s you MAY Not need these????
Right side cabin to engine comp harness 32100-S3M-A12
Left side cabin to engine comp harness 32120-S3M-A20

I Would attempt with out (that i bought and used with out trying without first) It will make not having to do all the rewiring of
that i did.
Upper instrument harness 32117-S3M-A31
Lower dash harness 32150-S3M-A32

I copied fsttyms1's parts list of what's needed to make a 6 speed swap to happen for a TL 2nd gen or a CL 2nd gen replacement. All the parts that say check next to them are the parts that I have. I bought all these parts basically brand new except for the starter,cluster(123k miles) shifter assembly, shifter cables, and heated seat switch. Starter has been tested and works good and original. The reason why I am selling the parts is that I do not have the time because of a new job and I will be selling my 03 TL-S that this was supposed to go to. My loss your gain. I would like to sell all as a whole. Everything besides the parts listed above that are used are still in the boxes packaged and ready to go

03 tls nc

iTrader: (6)

Pm'd about parking brake....

AcraAdi93

Starter and cluster --SoLd--

AcraAdi93

Handbrake, cupholder, heated seat switch, equalizer, equalizer pin, spring, and nut with parking brake --SoLd--

DEPTLS

iTrader: (6)

Do you have NEW Engine mounts? and are they oem?

AcraAdi93

Nope don't have the mounts

AcraAdi93

To anyone who sees this thread please read the notes I made under the list. I mentioned that anything that has check in parenthesis are the parts that I have. And the parts that I mentioned that are sold, are sold. Thank you

AznWay

iTrader: (8)

To much to read.... So i had to edit for you....

03 CLs-6 Flywheel bolts (Qty 8) 90011-PGE-000 (CHECK)
03 CLs-6 Shifter and cables. 54100-S3M-A01, 54310-S3M-A01 (check)
03 CLs-6 Hydraulic Clutch lines. 46960-S3M-A01, & 46970-S3M-A01 (CHECK)
Front plate assembly (behind cam pulley) 11860-PGE-A10 (CHECK)
Crank shaft sensor 37500-PGE-A11 (CHECK)
TDC SUB HARNESS 37841-PGE-A10 (CHECK)
BRAKE PEDAL ASSY 46600-S3M-A51 (CHECK)
CLUTCH PEDAL 46910-S3M-A01 & CLUTCH PEDAL BRACKET 46990-S84-A01 (check)
Shift Boot 83414-S3M-A01ZA (check)
Shift Knob 54102-SL0-023ZB (check)

Tariqtiki

How much for the shift knob?

Ron A

Especially if you're like me and don't understand most of it, but I guess the people that are interested can understand it and that's what's important.

AznWay

iTrader: (8)

I'm trying buy some part in few days (maybe) trying to double check what he had. Before i started order my stuff.

Matt Mergenthal

Still have manual ECU???

AcraAdi93

I still have the clutch pedal with bracket, brake pedal, shifter assembly, shift knob, shifter cables, speedometer, crankshaft sensor, tdc subharness, and flywheel bolts

AcraAdi93

I had another speedometer laying around that I forgot about and it is in good condition. Has about 142k miles on it

DEPTLS

iTrader: (6)

What about the Brackets for the oem Torque Dampners? do you have them?

AcraAdi93

No I do not have those

AcraAdi93

Mod please close this thread. I will make a new one that is more easier to understand.