bigg_86

iTrader: (1)

Category: Accessories
Price: $6000
Private or Vendor Listing: Private Listing
Part Fits (you may select multiples): Integra, Other Honda/Acura
Location (State/Prov/Terr): OH
Item Condition: Used

THIS WILL BE SOLD AS A PACKAGE, IM NOT PARTING OUT.
6,000 OBO

BLOCK
B18B1
- MICRO-POLISHED AND BALANCED HONDA CRANKSHAFT (0.10 UNDER)
- NEW CRANKSHAFT BEARINGS AND THRUST BEARINGS
- NEW FRONT AND REAR MAIN SEALS
- "INLINE 4" NEW SINGLE BELT FORGED ALUMINUM CRANK PULLEY (NOT EBAY CRAP)
- DARTON CAST IRON SLEEVES BORED TO 84MM (2.0L) - over $1k on labor
- BRAND NEW WISECO PISTONS (will disclose compression ratio to BUYER ONLY)
- MODIFIED EAGLE RODS WITH NEW BEARINGS
- APR HEAD STUDS
- NEW OEM WATER PUMP
- NEW MODIFIED OEM OIL PUMP (SHOULD INCREASE PRESSURE BY 20-30%)
- NEW TIMING BELT
- NEW OEM PULLEYS AND TENSIONER
- NEW ALUMINUM OIL PAN WITH OIL RETURN FITTING

HEAD
- B18A1
- FULL EXTREME PORT & POLISHED JOB ($1500 LABOR)
- NEW FERREA VALVE GUIDES
- THREE ANGLE VALVE JOB
- HIGH FLOW FORGED VALVES, OVERSIZED +1mm INTAKE- +1mm exhaust
- NEW BRIAN CROWER TITANIUM RETAINERS AND DUAL SPRINGS
- BRIAN CROWER STATE 2 BOOST CAMSHAFTS
- STR ADJUSTABLE CAM GEARS
- CHROMED VALVE COVER

INTAKE
- SKUNK 2 PORT & POLISHED INTAKE MANIFOLD (MODIFIED FOR EXTRA VACUUM LINES)
-WILL INCLUDE MAP3 SENSOR
- SKUNK 2 70mm THROTTLE BODY

EXHAUST
- 3 INCH DOWNPIPE (4 BOLT TURBO FLANGE)
- HIGH FLOW CAT
- 3 INCH CATBACK (RESONATED)

CHASSIS
- 95 HONDA CIVIC CX
- INTEGRA GSR LEATHER FRONT SEATS
- CUSTOM REAR LEATHER SEATS TO MATCH FRONT SEATS
- POLYURETHANE FRON LIP
- BUDDY CLUB SIDE SKIRTS AND REAR BUMPER
- FULL ADJUSTABLE COIL OVER KIT
- FRONT SKUNK 2 ADJUSTABLE CAMBER KIT
- REAR ADJUSTABLE CAMBER KIT
- REAR BRAKE DISK CONVERSION
- NEW PADS AND ROTORS
- MID 3 piece wing
- CARBON FIBER UPPER JDM WING
- NEW FRONT WHEEL BEARINGS
- NEW FRONT TIE RODS
- NEW FRONT UPPER AND LOWER BALL JOINTS

FUEL SYSTEM
- WALBRO 255LPH FUEL PUMP
- AEROMOTIVE HIGH FLOW FUEL FILTER
- AEROMOTIVE FUEL PRESSURE REGULATOR WITH GAUGE
- AEM FUEL RAIL
- 880cc INJECTORS
- MSD 6AL AND EXTERNAL COIL

TRANSMISSION
-B18C
- NEW CUSTCO LSD
- REPLACED ALL BEARINGS AND SEALS
- SKUNK 2 SHORT SHIFTER AND SHIFT KNOB
- AI4-XXG6 ACT CLUTCH KIT (TORQUE: 486 FT/LBS) LOAD CLAMP INCREASE OVER 145%
- 8LBS FIDANZA ALUMINUM FLYWHEEL
- 400HP AXLES (one boot needs to be replaced since i cracked it when i was pulling it out but they are in good shape)

TURBO PARTS
- HORN STYLE EXHAUST MANIFOLD (MODIFIED TO FIT T03/T04 AND T4 TURBOS)
- NEW TIAL 44mm WASTEGATE
- 32 X 12 X 3 FRONT MOUNT INTERCOOLER WITH COMPLETE PIPING
- BLOW-OFF VALVE

EASILY OVER $12K INVESTED. TAKE IT AS IS (EVERYTHING LISTED) FOR $6K,
it comes with a SET OF 15" ROTA WHEELS WITH NEW G-FORCE DRAG RADIALS TIRES IN THE FRONT AND NITTO GENS IN THE REAR COST OVER $1K


THE ENGINE IS CURRENTLY SITTING IN THE ENGINE STAND. as i stated before this is a project car. Im about to have knee surgery so I am not able to put the engine back in the car.

needs new brake booster, master cylinder, turbo (at least .50 trim), and a GOOD ASS TUNE.


if u have any questions txt me 216-402- 6 zero zero 5

rossv1

GLWS

bigg_86

iTrader: (1)

ttt