Jon’s slow Type-S & Mustang Progress Thread
#367
Moderator
Chapter Leader (South Florida Region)
Chapter Leader (South Florida Region)
iTrader: (6)
Joined: Sep 2008
Posts: 78,016
Likes: 20,032
badass!
do you follow alxxpress on IG?
He's my very close friend's uncle...he's been turbo'ing fox bodies for a long time...
first fast car i ever drove was his 280 on 26 pounds...first burnout i ever did was
his 70's corolla we called the peanut
do you follow alxxpress on IG?
He's my very close friend's uncle...he's been turbo'ing fox bodies for a long time...
first fast car i ever drove was his 280 on 26 pounds...first burnout i ever did was
his 70's corolla we called the peanut
#368
I do not have IG but Ive been thinking about getting back into some type of social media. Sounds like a cool dude with some good builds though, this should be a burnout queen
#370
Hahahaha yup no wheel hop here. Aftermarket upper and lower control arms and of course welded in subframe connectors. I have tooooooo much money into this thing but its been with me for 15 years lol
The following users liked this post:
90foxnotch (01-03-2020)
The following users liked this post:
rockstar143 (01-21-2020)
#373
Yess! White and a Notch! No better combo in my opinion. On top of that, Coyote swapped AND a big snail! So awesome!
EDIT: Just read the entire thread. Well done on the TL! Love everything done. I bet opening your garage door puts a big smile on your face haha.
EDIT: Just read the entire thread. Well done on the TL! Love everything done. I bet opening your garage door puts a big smile on your face haha.
Last edited by Ryan L21; 01-19-2020 at 11:57 PM.
#374
Thank you sir! Yeah I’ve put a lot of time into both cars. The TL is so awesome though, it was neglected before I bought it and I like where it is as of now. In the spring I’ll do a photo shoot of both cars. And hopefully a burnout pic of the notch haha
#376
That shit won't be done... Don't get us excited!
The following users liked this post:
rockstar143 (01-21-2020)
#378
#379
I bet! I would love to have a project like this one day. As you know my truck is getting a new motor dropped in at the moment. Down the road when the truck is rotted out, I can pull the 6.0L, that is going in, and get it bored .030 over and put that into a body and boost it! Maybe by then I will have some funds saved up to pay for it! Little do I know I will probably have 6 kids and be living off the state.
#380
Hhahahaha that is a pretty good plan. I f I were you Id just get that truck done and then get the bike done and have some fun. You could always just boost the truck that way a couple kids can have fun in the back!
#382
So I went with oem ball joints, oem upper control arms, nsk wheel bearings, and got some pci compliance bushings from a member on here. Also replacing outer tie rods and sway bar end links
#384
Turbo fab is all complete except for the bov. I am super impressed with my friends work, welds and location of everything is awesome. Now I need to keep up with the progress and start wiring and plumbing. To keep the car a street car I did not want the exhaust to dump out the front, so the exhaust goes through the driver side fender/suspension area. I’m hoping to keep it sleeper as possible but as soon as that hood opens it’s all business.
#393
The guy is an animal. Once he got it he had it back to me in like 2 days. And yes, this thing should drive really well I’m hoping. It wasn’t that bad honestly just want to get it all done at same time
#394
Caliper progressThat’s
The compressor I used to media blast didn’t do the best job so after this pic I sanded the rest by hand
Self etching primer
Can’t wait to see them on with new rotors
#398
I torqued all the suspension down with the arm jacked up. I think the calipers look great. Just need to install the rear calipers n brakes, bleed them, then I’ll get a pic with wheels on
He can’t wait to go for a ride