Introducing RV6 V3 Precat Deletes Taking Deposits
#321
All motor
This weekend for sure, guys. I had everything loosened up and/or out this past Sunday (rear cat bolts were easy), but hit a snag on the bolts from the race pipe to catback. I was on my back using ramps and those bolts were rusted pretty badly. I'm taking it somewhere with a lift Saturday to get the bolts changed, then doing the install Sunday.
#323
contemplating future mods
iTrader: (4)
My new install date is May 7th. The HFPC will be installed with out any doubts!!! I have enlisted the assistance of a professional and he assured me that there would not be any problems with the install. If it goes well I will hand him out a recommendation here on Acurazine
I already have the before (in cabin) clip. If there are any other before and after type clips that you want please let me know.
My mods are an AEM CAI and RV-6 V3 J-Pipe.
I will also be installing (whenever it gets shipped), the RV-6 Exhaust. I will try to get some clips for each part of the installation.
I already have the before (in cabin) clip. If there are any other before and after type clips that you want please let me know.
My mods are an AEM CAI and RV-6 V3 J-Pipe.
I will also be installing (whenever it gets shipped), the RV-6 Exhaust. I will try to get some clips for each part of the installation.
#324
UA6mt NBP
so am i getting this rite the pcd's cause a rasp and the hfc's do not i am looking for the non rasp i think that sounds horrible in the video. all i will be running is rv6 v3 jpipe and aem cai and a stage 3 exhaust with either the pcd or the hfc which ever one causes no rasp
Last edited by akertulis; 04-30-2011 at 08:01 PM.
#325
UA6mt NBP
so am i getting this rite the pcd's cause a rasp and the hfc's do not i am looking for the non rasp i think that sounds horrible in the video. all i will be running is rv6 v3 jpipe and aem cai and a stage 3 exhaust with either the pcd or the hfc which ever one causes no rasp
#326
Suzuka Master
iTrader: (2)
My new install date is May 7th. The HFPC will be installed with out any doubts!!! I have enlisted the assistance of a professional and he assured me that there would not be any problems with the install. If it goes well I will hand him out a recommendation here on Acurazine
I already have the before (in cabin) clip. If there are any other before and after type clips that you want please let me know.
My mods are an AEM CAI and RV-6 V3 J-Pipe.
I will also be installing (whenever it gets shipped), the RV-6 Exhaust. I will try to get some clips for each part of the installation.
I already have the before (in cabin) clip. If there are any other before and after type clips that you want please let me know.
My mods are an AEM CAI and RV-6 V3 J-Pipe.
I will also be installing (whenever it gets shipped), the RV-6 Exhaust. I will try to get some clips for each part of the installation.
Anyway, I had a shop get out the rusted bolts today, so tomorrow should be smooth sailing.
#331
Suzuka Master
iTrader: (2)
Cats are on and the car sounds absolutely sick. Slightly louder and more aggressive, with a really cool, pronounced gurgle on shifts. No rasp.
The car pulls so much more freely at all revs, too. It's the same feeling I had when I put the J and race pipes on.
I'll try to get some clips up tomorrow night, both in car and out!
The car pulls so much more freely at all revs, too. It's the same feeling I had when I put the J and race pipes on.
I'll try to get some clips up tomorrow night, both in car and out!
#332
AM To WDP In My Garage
iTrader: (40)
Cats are on and the car sounds absolutely sick. Slightly louder and more aggressive, with a really cool, pronounced gurgle on shifts. No rasp.
The car pulls so much more freely at all revs, too. It's the same feeling I had when I put the J and race pipes on.
I'll try to get some clips up tomorrow night, both in car and out!
The car pulls so much more freely at all revs, too. It's the same feeling I had when I put the J and race pipes on.
I'll try to get some clips up tomorrow night, both in car and out!
#333
BANNED
iTrader: (33)
so am i getting this rite the pcd's cause a rasp and the hfc's do not i am looking for the non rasp i think that sounds horrible in the video. all i will be running is rv6 v3 jpipe and aem cai and a stage 3 exhaust with either the pcd or the hfc which ever one causes no rasp
my setup is aemv2, v3 pcds, v3 jpipe, xlr8 non-res quads.
i got a mangaflow#10426 resonator welded in, no more rasp whatsoever.
#335
BANNED
iTrader: (33)
yes i noticed crazy good gains with the deletes, especially in the high rpms...car loves to pull and never quits.
favorite bolt-on to date. buy them, along with that #10426resonator...and you'll be in great shape. zero rasp.
#337
All motor
Cats are on and the car sounds absolutely sick. Slightly louder and more aggressive, with a really cool, pronounced gurgle on shifts. No rasp.
The car pulls so much more freely at all revs, too. It's the same feeling I had when I put the J and race pipes on.
I'll try to get some clips up tomorrow night, both in car and out!
The car pulls so much more freely at all revs, too. It's the same feeling I had when I put the J and race pipes on.
I'll try to get some clips up tomorrow night, both in car and out!
#338
Suzuka Master
iTrader: (2)
Ok, I take back what I said about it feeling like it did after the J/race pipe install. This is more pronounced. I'm not experiencing the feeling that these only show on the top end like some guys get with the deletes either; the car feels stronger everywhere in the rev range. So glad I waited for these rather than doing the deletes and then in all probability having to hack up my exhaust to add another resonator. Granted, I'd probably gain 5-7 whp with full deletes and fully non resonated exhaust, but I'll get that from porting the intake and runners. Just having the high flow primaries and the small original resonator on the Billy Boat is perfect, sound wise.
Be patient on the clips guys. As soon as it dries up to the point where I can set my camera on the side of the road, I'll do some drive bys and also an in car.
Be patient on the clips guys. As soon as it dries up to the point where I can set my camera on the side of the road, I'll do some drive bys and also an in car.
Last edited by anx1300c; 05-03-2011 at 06:59 PM.
#340
Burning Brakes
iTrader: (2)
Ok, I take back what I said about it feeling like it did after the J/race pipe install. This is more pronounced. I'm not experiencing the feeling that these only show on the top end like some guys get with the deletes either; the car feels stronger everywhere in the rev range. So glad I waited for these rather than doing the deletes and then in all probability having to hack up my exhaust to add another resonator. Granted, I'd probably gain 5-7 whp with full deletes and fully non resonated exhaust, but I'll get that from porting the intake and runners. Just having the high flow primaries and the small original resonator on the Billy Boat is perfect, sound wise.
Be patient on the clips guys. As soon as it dries up to the point where I can set my camera on the side of the road, I'll do some drive bys and also an in car.
Be patient on the clips guys. As soon as it dries up to the point where I can set my camera on the side of the road, I'll do some drive bys and also an in car.
hows the smell??
supposedly the hi flow cats are not supposed to smell
#342
contemplating future mods
iTrader: (4)
HFPC's will be installed tomorrow. I will be posting vids as soon as it is done. I'm hoping it will be finished by 1:00 PM Saturday (Eastern Time)
I will post in cabin before and afters as well as WOT drive bys before and afters.
and for an added bonus, I will post car at idle and normal RPM drive by.
Keep your fingers crossed that there will be no "speed bumps" with the install
I will post in cabin before and afters as well as WOT drive bys before and afters.
and for an added bonus, I will post car at idle and normal RPM drive by.
Keep your fingers crossed that there will be no "speed bumps" with the install
#352
Moderator
iTrader: (1)
^you didnt get the email?
Since, I paid in full already, i can disregard the links. am still waiting for a shipping #. should be soon. like in the next couple of days. i hope.
Originally Posted by Richie v6
Hello Everyone,
I just wanted to inform everyone that the castings for the V3 PCDs and HFPC are in. You can make your final payments using the following links and I will ship ASAP. If you have any questions feel free to ask.
Regards,
Rich
PCDs
http://rv6-performance.com/index.php...mart&Itemid=83
HFPCs
http://rv6-performance.com/index.php...mart&Itemid=96
I just wanted to inform everyone that the castings for the V3 PCDs and HFPC are in. You can make your final payments using the following links and I will ship ASAP. If you have any questions feel free to ask.
Regards,
Rich
PCDs
http://rv6-performance.com/index.php...mart&Itemid=83
HFPCs
http://rv6-performance.com/index.php...mart&Itemid=96
#355
Former Sponsor
Thread Starter
I printed the rest if the labels today for the PCDs and HFPCs will be shipped as soon as they are done. Maybe late next week.
#360
Former Sponsor
Thread Starter
Since the castings are in I will be ending the introductory pricing Monday you can lock in the price with a deposit. All PCDs preorders should be sent out by Monday. The shipping ETA for the HFPC will be the 22-27th.
http://rv6-performance.com/index.php...mart&Itemid=92
http://rv6-performance.com/index.php...mart&Itemid=92