Intermittent scraping noise when turning wheel
#1
Your Friendly Canadian
Thread Starter
Join Date: Dec 2007
Location: Toronto, Ontario
Age: 31
Posts: 17,428
Received 1,484 Likes
on
1,048 Posts
Intermittent scraping noise when turning wheel
Hey all.
Lately I've been getting a pretty loud and serious sound when turning the steering wheel. It's a sound similar to meat going through a grinder. Really painful to hear it coming from your car. It happens when I'm going above maybe 5 mph and giving the wheel more than a half turn.
It's not a constant sound, but intermittent. At first I thought it was something like the wheel spokes scraping against the brake caliper. The spokes would explain the intermittent part, and there is very little clearance between the wheel and caliper.
However, there's still some space between them, and what could cause that gap to close when turning?
The right wheel makes the sound when turning left, and vice versa. They don't make the sound at the same time.
Could it be something like a CV boot? I'm not too familiar with steering/suspension.
I need this car to make a 250 mile trip tomorrow night, any help would be greatly appreciated.
Car is a 2003 Accord, 4 cylinder AT with about 137k miles, or 220k kilometres.
Lately I've been getting a pretty loud and serious sound when turning the steering wheel. It's a sound similar to meat going through a grinder. Really painful to hear it coming from your car. It happens when I'm going above maybe 5 mph and giving the wheel more than a half turn.
It's not a constant sound, but intermittent. At first I thought it was something like the wheel spokes scraping against the brake caliper. The spokes would explain the intermittent part, and there is very little clearance between the wheel and caliper.
However, there's still some space between them, and what could cause that gap to close when turning?
The right wheel makes the sound when turning left, and vice versa. They don't make the sound at the same time.
Could it be something like a CV boot? I'm not too familiar with steering/suspension.
I need this car to make a 250 mile trip tomorrow night, any help would be greatly appreciated.
Car is a 2003 Accord, 4 cylinder AT with about 137k miles, or 220k kilometres.
#3
Stay Out Of the Left Lane
Join Date: Oct 2003
Location: SE Mass --- > Central VA --- > SE Mass
Age: 57
Posts: 8,953
Received 1,236 Likes
on
1,023 Posts
Not always but usually CV joints make a "clicking" sound when going bad.
You don't say if this is a recent thing and / or an ongoing issue.
By chance have you recently washed your car or driven in the rain where your rotors have gotten wet? As a thought you may have some rust on your rotors and when turning the rust could be contacting your calipers. However use of your brakes should remove any surface rust. How many miles on your current pads? Time for replacement?
Again just a couple of thoughts. As suggested above, you may want to pull your wheels and take a look.
You don't say if this is a recent thing and / or an ongoing issue.
By chance have you recently washed your car or driven in the rain where your rotors have gotten wet? As a thought you may have some rust on your rotors and when turning the rust could be contacting your calipers. However use of your brakes should remove any surface rust. How many miles on your current pads? Time for replacement?
Again just a couple of thoughts. As suggested above, you may want to pull your wheels and take a look.
#4
Team Owner
Vote for warped rotors.
#6
Your Friendly Canadian
Thread Starter
Join Date: Dec 2007
Location: Toronto, Ontario
Age: 31
Posts: 17,428
Received 1,484 Likes
on
1,048 Posts
Not rotors, today was the first time I washed the car in months, and the rotors aren't warped. I replaced them a few months back, and they still brake smoothly. And the swipe from the tire chunk is on the side of the bumper, so I think that it was just deflected and I didn't drive over it. Splash guards are fine and straight, nonetheless.
It did make a clicking sound for a while, the scraping is very recent. Like maybe two weeks ago, but I haven't driven the car much. Would I still be able to make my trip tomorrow?
How can I check for bad CV boots with the wheels off?
Thanks for the help, guys.
EDIT: FWIW The car drives perfectly fine, no steering issues or anything. The only telltale sound that something is off is the noise.
It did make a clicking sound for a while, the scraping is very recent. Like maybe two weeks ago, but I haven't driven the car much. Would I still be able to make my trip tomorrow?
How can I check for bad CV boots with the wheels off?
Thanks for the help, guys.
EDIT: FWIW The car drives perfectly fine, no steering issues or anything. The only telltale sound that something is off is the noise.
Last edited by Aman; 04-07-2012 at 08:53 PM.
#7
Your Friendly Canadian
Thread Starter
Join Date: Dec 2007
Location: Toronto, Ontario
Age: 31
Posts: 17,428
Received 1,484 Likes
on
1,048 Posts
Made the trip fine last night, but any significant gas application with the steering wheel fully turned sends a little kick back through the steering wheel.
I tried to replicate the sound for a friend last night, and it was much harder to do. Went back to a telltale clicking sound instead of a scraping noise. I guess that's good news, but I'm convinced it's a CV boot now.
I tried to replicate the sound for a friend last night, and it was much harder to do. Went back to a telltale clicking sound instead of a scraping noise. I guess that's good news, but I'm convinced it's a CV boot now.
Trending Topics
#8
Unofficial Goat
iTrader: (1)
if you suspect cv, check inside the wheels and underbody for grease being flung out. A torn boot will evacuate all the grease to either of these locations. If you turn the wheels to full lock and grab a flash light you should be able to spot a tear. This is basically what sound you should be expecting.
Thread
Thread Starter
Forum
Replies
Last Post
mada51589
3G TL Problems & Fixes
79
05-03-2022 08:54 PM
rockyboy
2G RDX (2013-2018)
46
01-25-2016 06:00 PM
acura, back, brakes, car, cl, intermitent, intermitten, metal, noise, scraping, scratching, tl, turning, wheel, wheels