DIY: ILX G1 Brake Light Swap. AFspec edition.
#1
Suzuka Master
Thread Starter
DIY: ILX G1 Brake Light Swap. AFspec edition.
Hello everyone.
Back with a DIY on changing your brakelights. The first DIY for the fogs can be found here: https://acurazine.com/forums/ilx-per...t-swap-944402/
This time I get to use some lighting from Thmanx/AFspec himself. You can find these lights and more at https://af-lighting.net/
These specific lights (red 280 30w) can be found here https://af-lighting.net/products/il4...ybrid-led-pair
Now on with the DIY.
Album DIY: ILX G1 Brakelight Swap - Album on Imgur
Use flat head screw driver to open small door to reach screws.
Two screws hold brake light in.
Pull brake light toward you. I put on hand on the left side and pull by putting two fingers behind the tab that had the screws holding it in.
That small white tab is why the brake light will only slide toward the back. Use that to secure the brake light back into place at the end.
Top (left) socket is the brake light while the bottom (right) socket is for the turn signal. Easiest to pop the bottom socket out first since there is no bulb attached. Then undo the top brake light which does have a real bulb.
OE brake light bulb.
Attachment 101791
OE bulb left. AFspec 280 30w red cone in the middle. That is what we are using. The two LEDs on the right are another style brake light offered by AFspec in red 20w.
Attachment 101792
OE output.
Attachment 101793
Aftermarket AFspec 280 30w output.
Attachment 101794
Left OE. Right AFspec 280 30w LEDs
Left OE. Right the 20w LEDs from AFspec.
Attachment 101796
OE
Attachment 101797
OE
Attachment 101798
AFSpec 280 30w
Attachment 101799
AFspec 280 30w
Attachment 101800
Left AFspec 20w LEDs. Right AFspec 280 30w
Attachment 101801
Left AFspec 20w LEDs & Right AFspec 280 30w on ground.
P.S. All unedited shots standing at the same spot for each comparison shot. These 30w projectors are truly brilliant. So damn bright. And they really light up the entire red housing while the OE bulbs can only really light up the small rectangle.
The 20w were great as well. In comparison to OE they still blow them away. In the comparison to the 30w projectors they look much dimmer. Those 30w LEDs are just nuts. Love it. And now I also have a back up set of 20w for the day these 30w go out.
Back with a DIY on changing your brakelights. The first DIY for the fogs can be found here: https://acurazine.com/forums/ilx-per...t-swap-944402/
This time I get to use some lighting from Thmanx/AFspec himself. You can find these lights and more at https://af-lighting.net/
These specific lights (red 280 30w) can be found here https://af-lighting.net/products/il4...ybrid-led-pair
Now on with the DIY.
Album DIY: ILX G1 Brakelight Swap - Album on Imgur
Use flat head screw driver to open small door to reach screws.
Two screws hold brake light in.
Pull brake light toward you. I put on hand on the left side and pull by putting two fingers behind the tab that had the screws holding it in.
That small white tab is why the brake light will only slide toward the back. Use that to secure the brake light back into place at the end.
Top (left) socket is the brake light while the bottom (right) socket is for the turn signal. Easiest to pop the bottom socket out first since there is no bulb attached. Then undo the top brake light which does have a real bulb.
OE brake light bulb.
Attachment 101791
OE bulb left. AFspec 280 30w red cone in the middle. That is what we are using. The two LEDs on the right are another style brake light offered by AFspec in red 20w.
Attachment 101792
OE output.
Attachment 101793
Aftermarket AFspec 280 30w output.
Attachment 101794
Left OE. Right AFspec 280 30w LEDs
Left OE. Right the 20w LEDs from AFspec.
Attachment 101796
OE
Attachment 101797
OE
Attachment 101798
AFSpec 280 30w
Attachment 101799
AFspec 280 30w
Attachment 101800
Left AFspec 20w LEDs. Right AFspec 280 30w
Attachment 101801
Left AFspec 20w LEDs & Right AFspec 280 30w on ground.
P.S. All unedited shots standing at the same spot for each comparison shot. These 30w projectors are truly brilliant. So damn bright. And they really light up the entire red housing while the OE bulbs can only really light up the small rectangle.
The 20w were great as well. In comparison to OE they still blow them away. In the comparison to the 30w projectors they look much dimmer. Those 30w LEDs are just nuts. Love it. And now I also have a back up set of 20w for the day these 30w go out.
Last edited by usdmJON; 05-02-2016 at 03:24 PM.
The following users liked this post:
Thmanx (05-03-2016)
#5
Suzuka Master
Thread Starter
Are you asking in regards to the turn signal?
Our signal uses the lower half while the brake light uses the top half. As for your specific question I frankly dont know. The top bulb is used for braking only while the bottom one is signaling only so I assume the brake light is a single filament.
Our signal uses the lower half while the brake light uses the top half. As for your specific question I frankly dont know. The top bulb is used for braking only while the bottom one is signaling only so I assume the brake light is a single filament.
#7
Suzuka Master
Thread Starter
lol Good! They shouldnt be that close to me. hahahaha
My neighbor is a cop. He saw me taking a pic with them on and asked me for the site I bought them from. His quote was "I bet that has stopping power." I think he approved.
My neighbor is a cop. He saw me taking a pic with them on and asked me for the site I bought them from. His quote was "I bet that has stopping power." I think he approved.
Trending Topics
The following users liked this post:
justnspace (09-07-2016)
#9
Suzuka Master
Thread Starter
Not sure if serious... That stuff was literally just for that pic as a joke because everyone else in the world puts alcohol on their tray and i dont drink so i put a dab rig and torch on it instead but i wouldnt be caught dead with that shit on my tray daily driving.
But the tray itself he has seen and didnt comment either way on. He used to own a civic with slight mods then got a truck to haul his kids. His wife has a little fusion he has lowered and thrown plastidip on the wheels since seeing my plastidip forever ago amd my suggestion on springs for a nice inch drop.
Only people here hate on the tray. But people here also love vossens, other shit wheels, ruin their cars with floor jacks, and cant install spacers themselves so frankly i could give a fuck less what 98% of these idiots think. If making fun of me makes them feel better at night when their wife goes to bed without giving them a reach around then by all means im not going to stop them.
But the tray itself he has seen and didnt comment either way on. He used to own a civic with slight mods then got a truck to haul his kids. His wife has a little fusion he has lowered and thrown plastidip on the wheels since seeing my plastidip forever ago amd my suggestion on springs for a nice inch drop.
Only people here hate on the tray. But people here also love vossens, other shit wheels, ruin their cars with floor jacks, and cant install spacers themselves so frankly i could give a fuck less what 98% of these idiots think. If making fun of me makes them feel better at night when their wife goes to bed without giving them a reach around then by all means im not going to stop them.
Last edited by usdmJON; 09-07-2016 at 11:21 AM.
#10
Senior Moderator
nice lights!!
#12
Jeff
iTrader: (3)
Join Date: Jul 2014
Location: Port City, New Brunswick Canada
Posts: 5,728
Received 815 Likes
on
726 Posts
yea that was nothing short of a little joke..... just poking fun at you man
Im not a big drinker at all... enjoy a beer every so often but I personally love dabs and medical grade bud! Im doing a cleanse at the moment for a job but as soon as they get my clean piss.... back to the dabs and med grade LOL
Im not a big drinker at all... enjoy a beer every so often but I personally love dabs and medical grade bud! Im doing a cleanse at the moment for a job but as soon as they get my clean piss.... back to the dabs and med grade LOL
#13
Suzuka Master
Thread Starter
#14
Suzuka Master
Thread Starter
yea that was nothing short of a little joke..... just poking fun at you man
Im not a big drinker at all... enjoy a beer every so often but I personally love dabs and medical grade bud! Im doing a cleanse at the moment for a job but as soon as they get my clean piss.... back to the dabs and med grade LOL
Im not a big drinker at all... enjoy a beer every so often but I personally love dabs and medical grade bud! Im doing a cleanse at the moment for a job but as soon as they get my clean piss.... back to the dabs and med grade LOL
#15
Are you asking in regards to the turn signal?
Our signal uses the lower half while the brake light uses the top half. As for your specific question I frankly dont know. The top bulb is used for braking only while the bottom one is signaling only so I assume the brake light is a single filament.
Our signal uses the lower half while the brake light uses the top half. As for your specific question I frankly dont know. The top bulb is used for braking only while the bottom one is signaling only so I assume the brake light is a single filament.
#16
Suzuka Master
Thread Starter
I thought our brake light bulb have one filament for the running tail light and the second filament for when you hit the brakes. Ive been wanting to change my rear turn signal and brake lights to led. im good as long as the bulbs brightens up when i hit the brakes. and do i need to get a resistor to use these bulbs?
Any questions like that if direct toward thamnx.
Last edited by usdmJON; 09-08-2016 at 12:07 PM.
Thread
Thread Starter
Forum
Replies
Last Post