Grilles, Grilles...and more Grilles!! Show/Give Ideas Here!
#202
I like to whistle in my
iTrader: (7)
I did a lot of sanding and primer with flat black and really light coats of clear( like dusting it). I even mixed in one or two coats of the trim paint. It came out pretty nice. I'll try to post pictures tomorrow. Probably wont be on the car until next weekend.
#203
Whatever I do what I want
iTrader: (3)
beat this!
Remove the front bumper,remove the factory grille,cut a mesh grille out from gutter guard(lowes or home depot will have). Insert the grill and cut notches where the factory grille would insert, so it pushes against your mesh grill holding it in place. With the factory grill I cut out the top and bottom lines oput leaving the center only.Quickest way to do this is with a dremel.I drilled a few holes in the center bar to ziptie the mesh to this factory insert. Next I sanded and painted the insert silver. During this time I mounted white CCFLs behind the lower grille.
I will take night pictures showing all the grille lights I added soon.
I will take night pictures showing all the grille lights I added soon.
#205
I like to whistle in my
iTrader: (7)
** 5 minute rule**
I picked up the grill from theWanderer - had a pretty good paint job so I had to sand through the clear and WDP paint.I sanded with some 180 - 320 - 600 and 800 ( I think those were the numbers). Started with just flat black primer. It was sandable so I went through a can of that to get it as smooth as possible. I did a couple wet sands too with a spray bottle. After doing that a few times I mixed in the Trim paint but it was too glossy for me so I went back to the just flat black( not the primer) then I dusted it a few times with the cleat coat. I sanded between every spray just FYI. I like it. Gonna do a water test today to see how it holds up with the hose and should be on in aabout a week.
I picked up the grill from theWanderer - had a pretty good paint job so I had to sand through the clear and WDP paint.I sanded with some 180 - 320 - 600 and 800 ( I think those were the numbers). Started with just flat black primer. It was sandable so I went through a can of that to get it as smooth as possible. I did a couple wet sands too with a spray bottle. After doing that a few times I mixed in the Trim paint but it was too glossy for me so I went back to the just flat black( not the primer) then I dusted it a few times with the cleat coat. I sanded between every spray just FYI. I like it. Gonna do a water test today to see how it holds up with the hose and should be on in aabout a week.
#206
Got The Midas Touch
Remove the front bumper,remove the factory grille,cut a mesh grille out from gutter guard(lowes or home depot will have). Insert the grill and cut notches where the factory grille would insert, so it pushes against your mesh grill holding it in place. With the factory grill I cut out the top and bottom lines oput leaving the center only.Quickest way to do this is with a dremel.I drilled a few holes in the center bar to ziptie the mesh to this factory insert. Next I sanded and painted the insert silver. During this time I mounted white CCFLs behind the lower grille.
I will take night pictures showing all the grille lights I added soon.
I will take night pictures showing all the grille lights I added soon.
I like the mesh look thats what Im thinking of doing for mine how shiny does the mesh look when you put it on?
#208
Whatever I do what I want
iTrader: (3)
From my experience with painting grilles it stays shiny for at least a couple months to a year. This time I used alot of adhesive promoter and several different coats of silver and chrome,then gave it plenty of time to cure.I hope this will keep the shine longer.
#211
FL 04 dgp TL
Join Date: Jan 2008
Location: sarasota, florida
Age: 41
Posts: 241
Likes: 0
Received 3 Likes
on
2 Posts
here's my grill. i like it bc no one in my city has it. DGP one of a kind.
https://acurazine.com/forums/picture...ictureid=11856
https://acurazine.com/forums/picture...ictureid=11856
#216
FL 04 dgp TL
Join Date: Jan 2008
Location: sarasota, florida
Age: 41
Posts: 241
Likes: 0
Received 3 Likes
on
2 Posts
http://cgi.ebay.com/ebaymotors/Acura...#ht_3807wt_911
wow your right. i never knew that. thats where i purchased my grill. wonder how they got the pics of my ride.
wow your right. i never knew that. thats where i purchased my grill. wonder how they got the pics of my ride.
#218
~Da Nocturnal Cheetah~
Thread Starter
#219
Rev High; Drive Happy
iTrader: (2)
Join Date: Feb 2008
Location: Scarborough, Ontario
Age: 34
Posts: 4,074
Received 398 Likes
on
332 Posts
http://cgi.ebay.com/ebaymotors/Acura...#ht_3807wt_911
wow your right. i never knew that. thats where i purchased my grill. wonder how they got the pics of my ride.
wow your right. i never knew that. thats where i purchased my grill. wonder how they got the pics of my ride.
#221
Drifting
iTrader: (13)
Painted my front grill with Trim Paint in flat black. I had to remove the bumper to get the gray area on the bottom. I also painted the lower grilles. I really like the way it sets off the ACURA dome decal.
My finishing touch---chrome door handle inserts which fit nicely in the recesses on the grill crossbar and flow nicely with the chrome strip in the headlights.
#223
Whatever I do what I want
iTrader: (3)
Fixed Picture Links
Remove the front bumper,remove the factory grille,cut a mesh grille out from gutter guard(lowes or home depot will have). Insert the grill and cut notches where the factory grille would insert, so it pushes against your mesh grill holding it in place. With the factory grill I cut out the top and bottom lines oput leaving the center only.Quickest way to do this is with a dremel.I drilled a few holes in the center bar to ziptie the mesh to this factory insert. Next I sanded and painted the insert silver. During this time I mounted white CCFLs behind the lower grille.
Trim the mesh where the plastic straight grill pushes in at.
Lining up the mesh cut outs
Notice the grey tabs where the mesh needs to be trimmed.
Place the factory plastic line grill on top of the mesh.
Push until it snaps in.
*Optional* Mount some blue cold cathodes (ccfl)
Cover any wires and reinstall bumper.
Night pictures will be added soon.
Trim the mesh where the plastic straight grill pushes in at.
Lining up the mesh cut outs
Notice the grey tabs where the mesh needs to be trimmed.
Place the factory plastic line grill on top of the mesh.
Push until it snaps in.
*Optional* Mount some blue cold cathodes (ccfl)
Cover any wires and reinstall bumper.
Night pictures will be added soon.
Some of the pictures weren't showing up so I switched to photo bucket, so let's see if they work better on their server.
#224
I like it murdered out! Plus, the red trim on the wheel/tires really sets it off well.
2009 Kansas City All Acura Meet-May 17th
https://acurazine.com/forums/midwest-312/kansas-city-2009-spring-all-acura-meet-may-17th-12pm-%40-jay-wolfe-acura-714994/
2009 Kansas City All Acura Meet-May 17th
https://acurazine.com/forums/midwest-312/kansas-city-2009-spring-all-acura-meet-may-17th-12pm-%40-jay-wolfe-acura-714994/
where did you get you grill?
how to install it? will it fit for 2005 acura TL MT?
thanks....
wolverine
#225
Advanced
yo this is for ACU-RATE.....
I have a 08 KBP type s and i recently installed the ebay grill like the one you have (had to have it custom fitted and stuff as well) check out what i found today....http://images.google.com/imgres?imgu...3Doff%26sa%3DX
scroll down the page this grill would have fit our cars no problem
I have a 08 KBP type s and i recently installed the ebay grill like the one you have (had to have it custom fitted and stuff as well) check out what i found today....http://images.google.com/imgres?imgu...3Doff%26sa%3DX
scroll down the page this grill would have fit our cars no problem
#228
Wish I had a Carrera.
Join Date: Sep 2003
Location: Bumphuck, AL
Age: 42
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
#231
Real Cars Have 3 Pedals
iTrader: (2)
yo this is for ACU-RATE.....
I have a 08 KBP type s and i recently installed the ebay grill like the one you have (had to have it custom fitted and stuff as well) check out what i found today....http://images.google.com/imgres?imgu...3Doff%26sa%3DX
scroll down the page this grill would have fit our cars no problem
I have a 08 KBP type s and i recently installed the ebay grill like the one you have (had to have it custom fitted and stuff as well) check out what i found today....http://images.google.com/imgres?imgu...3Doff%26sa%3DX
scroll down the page this grill would have fit our cars no problem
I actually bought my grille off another TL owner who didn't like the way it looked, so he sold it to me for $100...
& ever since he seen it installed on my ride, he regrets selling it
ur KBP lookz really clean bye the way.
P.S. feel free to put the Type-s emblem in the front grill now.....Tell everyone its ACU-RATE approved....lol
Last edited by ACU-RATE; 08-10-2009 at 01:36 PM.
#234
Rev High; Drive Happy
iTrader: (2)
Join Date: Feb 2008
Location: Scarborough, Ontario
Age: 34
Posts: 4,074
Received 398 Likes
on
332 Posts
Well... I thought that too... but then the vent curves to the right [toward the air filter]. If it was turned the other way the vent would face left [away from the air filter].
#236
Rev High; Drive Happy
iTrader: (2)
Join Date: Feb 2008
Location: Scarborough, Ontario
Age: 34
Posts: 4,074
Received 398 Likes
on
332 Posts
It's actually not that complicated...
I like my headlights too... I think my ambers are TOO smoked though.
#238
RPF1+RS3 FTW
iTrader: (6)
Dude Komodo your car is dirty as hell lol reminds me of my friends 350Z he never washes it
heres a newer pic of my grill to keep this on topic
Paintmatched Trim | Paintmatched Crossbar | Gloss Black Emblem | Gloss Black Lower Piece
heres a newer pic of my grill to keep this on topic
Paintmatched Trim | Paintmatched Crossbar | Gloss Black Emblem | Gloss Black Lower Piece
Last edited by AnthraciteAspec; 08-14-2009 at 02:33 AM.
The following users liked this post:
IIDXholic (01-26-2012)
#239
Rev High; Drive Happy
iTrader: (2)
Join Date: Feb 2008
Location: Scarborough, Ontario
Age: 34
Posts: 4,074
Received 398 Likes
on
332 Posts
I accidently got fiberglass resin on the front bumper so now it looks like she's foaming from the mouth [grille].
Also her brakes are finito. I have no brake-pedal-feel... VSA light [and the hazard symbol] are now on.
So I can't drive her to get a wash... It's been two weeks. Got no money and no job... broke as hell right now =[
Nice TL, btw.
And are those Type-S diffusers I see?