Miyagi__'s Progress Thread
#205
Everyday I'm rofling
Independent fogs!
Some advice: connect the signal source from the relay to a fuse inside the cabin instead of the fusebox in the engine bay. I chose the windshield wiper fuse, number 4 I think.
Some advice: connect the signal source from the relay to a fuse inside the cabin instead of the fusebox in the engine bay. I chose the windshield wiper fuse, number 4 I think.
#206
Safety Car
The following users liked this post:
MC MiYoung3269 (04-30-2013)
#210
Instructor
Thread Starter
Whats the reason you put yours inside?
and is this fuse located beneath the plastic next to the VSA?
#211
Instructor
Thread Starter
nvm! found our post op! but damn i already connected it. i agree with your post in DIY independent fog thread, this would have saved me a lot of wire and time.... i took so much time trying to push two wires into the firewall. -.-
Everything is plugged up! but not getting any results.... my fogs won't turn on with the switch. wack.
Everything is plugged up! but not getting any results.... my fogs won't turn on with the switch. wack.
#215
Everyday I'm rofling
First thing I would check would be if all your wires are connected to the right terminals on the relay. Then I would check your fog light fuse.
The following users liked this post:
Miyagi__ (05-02-2013)
The following users liked this post:
Miyagi__ (05-02-2013)
#217
Instructor
Thread Starter
Does the amp of the relay matter? I figured out I'm using a 14 gauge wire on a 18-20 gauge wire so that may be causing a short.. Gay. I might have to replace the fuse. I hate life
#218
your fogs are so independent now they have stopped responding to your switch. they'll work when they damn well please!
The following 2 users liked this post by drivedata:
iSeeYouTwo (05-08-2013),
MC MiYoung3269 (05-02-2013)
#221
Instructor
Thread Starter
#222
Instructor
Thread Starter
K I'm dumb. What is a fuse holder for guys?
Oh I dunno. Maybe to hold a fuse to get my shit working.
Problem solved. Lol. Will post pics later. Nothing biggie.
Oh I dunno. Maybe to hold a fuse to get my shit working.
Problem solved. Lol. Will post pics later. Nothing biggie.
#226
watt = volt*amp
55+55 = 12*amp
9.1 = amp
yea I think I'd do a 15A fuse, 10A doesn't give you much room for real world conditions/tolerances.
#227
ROTAREDOM
This is why I hate electrical lol, that would have been really frustrating.
The following 2 users liked this post by ssjoeboe9:
MC MiYoung3269 (05-05-2013),
Miyagi__ (05-05-2013)
#228
Instructor
Thread Starter
I haven't been on here in a while... but this is my most recent update haha:
Cleared headlights
5k Switchbacks V2 VLED (its hyper flashing, but not going to install resistors (i'm lazy)
Removed laminX yellow film
6k HID fogs and 6k HID low beams
Removed Nokya hyper yellow high beams, installed the OEM high beams
Removed plasti-dipped grille
http://www.flickr.com/photos/95698458@N05/9593906699/http://www.flickr.com/photos/95698458@N05/9593906699/ by http://www.flickr.com/people/95698458@N05/, on Flickr
Cleared headlights
5k Switchbacks V2 VLED (its hyper flashing, but not going to install resistors (i'm lazy)
Removed laminX yellow film
6k HID fogs and 6k HID low beams
Removed Nokya hyper yellow high beams, installed the OEM high beams
Removed plasti-dipped grille
http://www.flickr.com/photos/95698458@N05/9593906699/http://www.flickr.com/photos/95698458@N05/9593906699/ by http://www.flickr.com/people/95698458@N05/, on Flickr
Last edited by Miyagi__; 08-25-2013 at 09:11 PM.
#231
Instructor
Thread Starter
#237
Instructor
Thread Starter
Thanks for the compliments guys! I want to do so much more. D':
btw, my independent fog light switch is practically useless now. I only installed it to match yellow fogs with yellow high beams. Now i gotta cut and remove all the wires i took so long to install. gey.
btw, my independent fog light switch is practically useless now. I only installed it to match yellow fogs with yellow high beams. Now i gotta cut and remove all the wires i took so long to install. gey.
#238
mr_tsxranjha
how did u clear the headlights? did u bake to get the amber out from the sides or u got new headlights? looking to install switchbacks also but dont want hyper flashing. lmk bout the clear sides!
I haven't been on here in a while... but this is my most recent update haha:
Cleared headlights
5k Switchbacks V2 VLED (its hyper flashing, but not going to install resistors (i'm lazy)
Removed laminX yellow film
6k HID fogs and 6k HID low beams
Removed Nokya hyper yellow high beams, installed the OEM high beams
Removed plasti-dipped grille
005-edit by freshtee00, on Flickr
Cleared headlights
5k Switchbacks V2 VLED (its hyper flashing, but not going to install resistors (i'm lazy)
Removed laminX yellow film
6k HID fogs and 6k HID low beams
Removed Nokya hyper yellow high beams, installed the OEM high beams
Removed plasti-dipped grille
005-edit by freshtee00, on Flickr
The following users liked this post:
Miyagi__ (08-28-2013)
#240
Instructor
Thread Starter
Yeah i just baked them myself. If you don't want hyper flashing, you would need to get load resistors and splice into the wires. Its an easy install!